Its too bad that we don't more folks from Oz on this list to get their input
on such matters as these. Malcolm, would you mention the MMM list in your
newsletter.....subscribing procedures are listed at the bottom of this email.
Thanks
Terry
In a message dated 11/13/2004 2:19:32 AM Pacific Standard Time,
p.green@mgk3.co.uk writes:
> Subj:Re: Distributor Clamps (was Lights- head lamps)
> Date:11/13/2004 2:19:32 AM Pacific Standard Time
> From: p.green@mgk3.co.uk (Peter Green)
> Sender: owner-mg-mmm@Autox.Team.Net
> Reply-to: <A HREF="mailto:p.green@mgk3.co.uk";>p.green@mgk3.co.uk</A> (Peter
>Green)
> To: lpalmer@roundaboutmanor.com (Lew Palmer), mgtom@bright.net ('tom
> metcalf'), jnshardy@earthlink.net ('Jack Hardy'), mg-mmm@Autox.Team.Net
>('MMM')
>
>
>
>
> Lew,
>
> I have an original PB parts list and it also does not list the vernier type
> clamp, I am not sure of its date but I did look at it to see if one was
> listed at the beginning of this debate.
>
> Peter.
>
>
> ----- Original Message -----
> From: "Lew Palmer" <lpalmer@roundaboutmanor.com>
> To: "'tom metcalf'" <mgtom@bright.net>; "'Jack Hardy'"
> <jnshardy@earthlink.net>; "'MMM'" <mg-mmm@Autox.Team.Net>
> Sent: Saturday, November 13, 2004 1:26 AM
> Subject: RE: Distributor Clamps (was Lights- head lamps)
>
>
> > Apparently, the mystery continues.
> >
> > Does anyone have a PB parts list that might show the different clamp might
> > have been used on PB production at some time? My copy is late enough
> > (1945)
> > but doesn't list the part separately.
> >
> > For people joinging this thread late, see
> > http://www.roundaboutmanor.com/airline/distclamps.htm
> > And tell us the source of the clamp marked "?"
> >
> > Cheers,
> > Lew Palmer
> >
> > -----Original Message-----
> > From: owner-mg-mmm@Autox.Team.Net [mailto:owner-mg-mmm@Autox.Team.Net] On
> > Behalf Of tom metcalf
> > Sent: Friday, November 12, 2004 7:19 AM
> > To: Jack Hardy; MMM; Lew Palmer
> > Subject: Re: Distributor Clamps (was Lights- head lamps)
> >
> > Jack , that's exactly the same clamp my PB has, too.
> >
> > tommm
> >
> >
> >
> > ----- Original Message -----
> > From: "Jack Hardy" <jnshardy@earthlink.net>
> > To: "MMM" <mg-mmm@Autox.Team.Net>; "Lew Palmer"
> > <lpalmer@roundaboutmanor.com>
> > Sent: Thursday, November 11, 2004 5:31 PM
> > Subject: Re: Distributor Clamps (was Lights- head lamps)
> >
> >
> >> All MMMers,
> >>
> >> My PA1875 came to me with it's engine modified to PB spec. and a
> >> microadjuster on the distributor the same as marked, "?" in the photos.
> >> The
> >> adjuster is very worn and allowed the timing to change +- several
> >> degrees.
> >
> >> I
> >> do not have a non-vernier adjusting type, I locked it in place with a
> >> modified large area washer under the mounting bolt & clamping the
> >> moveable
> >> part. I realize that this does not help determine the source of this
> >> part,
> >> but, for what it's worth, I wanted to report another P type with this
> >> microadjuster.
> >>
> >>
> >> Jack Hardy
> >
> > /// unsubscribe/change address requests to majordomo@autox.team.net or
> > try
> > /// http://www.team.net/cgi-bin/majorcool
> > /// http://www.team.net/mailman/listinfo
> > /// Archives at http://www.team.net/archive/mg-mmm
> > ///
/// unsubscribe/change address requests to majordomo@autox.team.net or try
/// http://www.team.net/cgi-bin/majorcool
/// http://www.team.net/mailman/listinfo
/// Archives at http://www.team.net/archive/mg-mmm
/// Send list postings to mg-mmm@autox.team.net
|