Long shot, but I had bad running issues - I could get it to idle but when I
reved it up, it would sputter badly then shut down. It was the condenser
wire inside the dizzy. It looked fine but the wire strands were broken.
On 12/9/12 10:21 PM, "Roy Haslett" <hrhaslett@yahoo.com> wrote:
> Sadly I am still in tuning hell. I have set the dwell to 52 degrees.
Checked
> all connections that they are clean and tight. When car ran it was rough
but
> I set the timing to 16 degrees at 600 rpm and verified the vacuum advance
was
> operating correctly and no leaks when revving engine. But, the car runs
like
> shit..super rough with the engine shaking like hell. Now, the car won't
even
> start?? Could I have some bad new iginition parts? Could my 6 month old
> Diamond coil have failed? Previous to attempting this tune up the car ran
a
> little weird with some very slight backfire but it ran great on the
highway.
> I don't think its a carb thing. Valves were checked 3 times. I don't get
it.
> Thanks
> Roy
>
>
>
> ________________________________
> From: Tim
> <tputland@charter.net>
> To: datsun-roadsters: autox.team.net
> <datsun-roadsters@autox.team.net>
> Sent: Wednesday, November 28, 2012 1:22 PM
> Subject: Re: [Roadsters] 1600 tuning issues
>
> I have (as usual) nothing new to
> add. But, I will echo what others have said as well as Paul below. And also
> add that my running issues got worse and worse on my tired 1600 as the
exhaust
> leak at the manifold got worse.
>
> Still waiting on my machinist to finish the
> head on my stroker. One step forward, two steps back.....sigh
>
> tim
>
>
> On Wed,
> Nov 28, 2012 at 3:16 PM, Paul Kort wrote:
>
>> Even on the race R16s, spinning
> up to 8000 rpms, we never had a timing
>> chain jump.
>>
>> back to basics,
> set the valve clearance, set the ignition timing, then
>> work on the carbs.
>>
>> Paul
>> Ohio
>>
>> On Wed, Nov 28, 2012 at 3:32 PM, Pete Peters
> <ppeters914@comcast.net> wrote:
>>
>>> According to Roy, the head was rebuilt
> at 5k; the motor at 20k (was the
>>> timing chain/gears replaced at that
> time?). Engine was running fine up
>>> until
>>> a few hundred miles ago, then
> slowly deteriorated.
>>>
>>> Wouldn't a timing chain jumping be instantly
> noticeable? And, while
>>> possible, has anyone experienced a 1600 timing chain
> jumping? Isn't that
>>> more likely in the OHC engines (U20, L-series)?
>>>
>>>
> My money is on something more simple like floats and/or exhaust/vacuum
>>>
> leaks.
>>>
>>> This has been a fun thread. Eagerly awaiting the resolution!
>>>
>>>
>>> Pete
>> ________________________________________
> ________________________________________
>
> datsun-roadsters@autox.team.net
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
> http://autox.team.net/mailman/options/datsun-roadsters/hrhaslett@yahoo.com
> ________________________________________
>
> datsun-roadsters@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
>
http://autox.team.net/mailman/options/datsun-roadsters/phillip.b.hall@msfc.na
s
> a.gov
________________________________________
datsun-roadsters@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe:
http://autox.team.net/mailman/options/datsun-roadsters/mharc@autox.team.net
|