--===============4703244466301682243==
Content-Transfer-Encoding: quoted-printable
<div>Please, please for your own sanity-remove the trans now from the =
engine-blocking the pan/rear plate and assemble the trans vertically to the=
OD with OD leg in a vice. As the last two notes advised-do not try to do =
it in the car-it will never align or you will damage the bronze bushing in =
the case and that cannot be replaced unless line bored correctly!</div>
<div> </div>
<div>It's not that difficult to do on the table-it just =
takes a bit of muscle and care. The lower the vice the better, or use a =
step stool and get up over the box solidly and lower it onto the OD...you =
will thank all of us if you do it that way, and curse yourself if you try =
to do it in the car. Hank</div>
<div><br>-------------------- <br><br>From:=
"JSARCH via Healeys" <healeys@autox.team.net> <br>Reply-To: "JSARCH"=
<jmsdarch@sbcglobal.net> <br>To: "'Al Fuller'" <alfuller194@gmail=
.com>, "'Leonard Berkowitz'" <drberkowitz@hotmail.com> <br>Cc: =
"'AH Mail List'" <healeys@autox.team.net> <br>Sent: August 28, 2025 =
at 12:15 PM PDT <br>Subject: Re: [Healeys] Advice and guidance needed for =
OD reinstallation </div>
<div class=3D"WordSection1">
<p class=3D"MsoNormal"><span style=3D"font-size: 11.0pt; font-family: =
'Calibri',sans-serif;">The first paragraph in this attachment describes =
lining up the sun wheel, planet carrier and roller clutch using the tool =
that Michel mentioned. You can also use a screwdriver as described in the =
workshop manual. In my experience it is extremely difficult to keep =
everything aligned when trying to mate the OD to the transmission with it =
in the car. Any slight movement of the driving flange, the part that bolts =
to the drive shaft, misaligns the internal components such that the third =
motion shaft cannot complete enter the OD.</span></p>
<p class=3D"MsoNormal"><span style=3D"font-size: 11.0pt; font-family: =
'Calibri',sans-serif;"> </span></p>
<div style=3D"border: none; =
border-top: solid #E1E1E1 1.0pt; padding: 3.0pt 0in 0in 0in;">
<p class=3D"MsoNormal"><strong><span style=3D"font-size: 11.0pt; =
font-family: 'Calibri',sans-serif;">From:</span></strong><span =
style=3D"font-size: 11.0pt; font-family: 'Calibri',sans-serif;"> Healeys =
<healeys-bounces@autox.team.net> <strong>On Behalf Of </strong>Al =
Fuller<br><strong>Sent:</strong> Wednesday, August 27, 2025 9:23 =
PM<br><strong>To:</strong> Leonard Berkowitz <drberkowitz@hotmail.=
com><br><strong>Cc:</strong> AH Mail List <healeys@autox.team.=
net><br><strong>Subject:</strong> Re: [Healeys] Advice and guidance =
needed for OD reinstallation</span></p>
</div>
<p class=3D"MsoNormal"> =
;</p>
<div>
<div>
<p class=3D"MsoNormal">Len, as regards your request for =
advice on remounting the overdrive - I would echo the advice from two prior=
posters: remove the gearbox, secure it on the bench input shaft down and =
install the OD there.</p>
</div>
<div>
<p class=3D"MsoNormal"> </p>
</div>
<div>
<p class=3D"MsoNormal">You'll thank them later...</p>
</div>
<div>
<p class=3D"MsoNormal"> </p>
</div>
<div>
<p class=3D"MsoNormal">________________<br>Sent from my phone <br>Best =
Regards,<br>Al Fuller</p>
</div>
</div>
<p class=3D"MsoNormal"> </p>
<div>
<div>
<p class=3D"MsoNormal">On Wed, Aug 27, 2025, 1:23<span =
style=3D"font-family: 'Arial',sans-serif;">=E2=80=AF</span>PM Leonard =
Berkowitz via Healeys <<a href=3D"mailto:healeys@autox.team.=
net">healeys@autox.team.net</a>> wrote:</p>
</div>
<blockquote style=3D"border: none; border-left: solid #CCCCCC 1.0pt; =
padding: 0in 0in 0in 6.0pt; margin-left: 4.8pt; margin-right: 0in;">
<div>
<div>
<p class=3D"MsoNormal"><span style=3D"font-family: 'inherit',=
serif;">Hi. All</span></p>
</div>
<div>
<p class=3D"MsoNormal"><span =
style=3D"font-family: 'inherit',serif;">I finally figured out how to get =
the OD out of my BJ7. Now for getting the new one installed. I found two =
rings sitting on the output shaft which I believe are fitted to the adapter=
plate. (See pics attached). The problem is going to be how to keep them in=
place while maneuvering the new OD into place. I was thinking of using =
either white lithium grease or wheel bearing grease. </span></p>
</div>
<div>
<p class=3D"MsoNormal"><span style=3D"font-family: 'inherit',=
serif;">Any suggestions? </span></p>
</div>
<div>
<p class=3D"MsoNormal"><span style=3D"font-family: 'inherit',serif;">Thank =
you in advance for any help you can offer. </span></p>
</div>
<div>
<p class=3D"MsoNormal"><span style=3D"font-family: 'inherit',=
serif;"> </span></p>
</div>
<div>
<p class=3D"MsoNormal"><span =
style=3D"font-family: 'inherit',serif;">Len Berkowitz </span></p>
</div>
</div>
<p class=3D"MsoNormal" style=3D"margin-bottom: 12.=
0pt;">_______________________________________________<br>Support Team.Net =
<a href=3D"http://www.team.net/donate.html"; target=3D"_blank" =
rel=3D"noopener">http://www.team.net/donate.html</a><br>Suggested annual =
donation $12.75<br><br>Archive: <a href=3D"http://www.team.=
net/pipermail/healeys" target=3D"_blank" rel=3D"noopener">http://www.team.=
net/pipermail/healeys</a> <a href=3D"http://autox.team.net/archive/healeys"=
target=3D"_blank" rel=3D"noopener">http://autox.team.=
net/archive/healeys</a><br><br><a href=3D"mailto:Healeys@autox.team.net"; =
target=3D"_blank" rel=3D"noopener">Healeys@autox.team.net</a><br><a =
href=3D"http://autox.team.net/mailman/listinfo/healeys"; target=3D"_blank" =
rel=3D"noopener">http://autox.team.net/mailman/listinfo/healeys</a><br><br>=
s/alfuller194@gmail.com" target=3D"_blank" rel=3D"noopener">http://autox.=
team.net/mailman/options/healeys/alfuller194@gmail.com</a></p>
</blockquote>
</div>
</div>
<div> </div>
--===============4703244466301682243==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys
http://autox.team.net/archive/healeys
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============4703244466301682243==--
|