This is a multi-part message in MIME format.
--===============4528208051400350220==
boundary="------------lKFlS30J0WUeFoSp5l3EkwOb"
Content-Language: en-US
This is a multi-part message in MIME format.
--------------lKFlS30J0WUeFoSp5l3EkwOb
Content-Transfer-Encoding: 7bit
Ok, just found it ... there's a set--single shim for the BJ8--on both
ends of the mainshaft.
On 8/27/2025 1:30 PM, Michael Salter wrote:
> Those "rings" are the Bellville washer and shim that go into the
> adaptor plate to eliminate end float of the mainshaft bearing.
>
>
>
>
> ------------------------------------------------------------------------
> *From:* Healeys <healeys-bounces@autox.team.net> on behalf of Leonard
> Berkowitz via Healeys <healeys@autox.team.net>
> *Sent:* Wednesday, August 27, 2025 3:50:01 PM
> *To:* healeys@autox.team.net <healeys@autox.team.net>
> *Subject:* [Healeys] Advice and guidance needed for OD reinstallation
> Hi. All
> I finally figured out how to get the OD out of my BJ7. Now for getting
> the new one installed. I found two rings sitting on the output shaft
> which I believe are fitted to the adapter plate. (See pics attached).
> The problem is going to be how to keep them in place while maneuvering
> the new OD into place. I was thinking of using either white lithium
> grease or wheel bearing grease.
> Any suggestions?
> Thank you in advance for any help you can offer.
>
> Len Berkowitz
>
--------------lKFlS30J0WUeFoSp5l3EkwOb
Content-Transfer-Encoding: 8bit
<!DOCTYPE html>
<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body>
Ok, just found it ... there's a set--single shim for the BJ8--on
both ends of the mainshaft.<br>
<br>
<br>
<div class="moz-cite-prefix">On 8/27/2025 1:30 PM, Michael Salter
wrote:<br>
</div>
<blockquote type="cite"
cite="mid:SN7PR22MB376494B52D382C8ABE46DA67A138A@SN7PR22MB3764.namprd22.prod.outlook.com">
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
<div
style="font-family: Aptos, Aptos_MSFontService, -apple-system, Roboto, Arial,
Helvetica, sans-serif; font-size: 12pt;"
dir="auto">
Those "rings" are the Bellville washer and shim that go into the
adaptor plate to eliminate end float of the mainshaft bearing.</div>
<div
style="font-family: Aptos, Aptos_MSFontService, -apple-system, Roboto, Arial,
Helvetica, sans-serif; font-size: 12pt;"
dir="auto">
<br>
</div>
<div
style="font-family: Aptos, Aptos_MSFontService, -apple-system, Roboto, Arial,
Helvetica, sans-serif; font-size: 12pt;"
dir="auto">
<br>
</div>
<div id="ms-outlook-mobile-body-separator-line" dir="auto"><br>
</div>
<div id="ms-outlook-mobile-signature" dir="auto"
style="font-family: Aptos, Aptos_MSFontService, -apple-system, Roboto, Arial,
Helvetica, sans-serif; font-size: 12pt;">
<div
style="font-family:Aptos, Aptos_MSFontService, -apple-system, Roboto, Arial,
Helvetica, sans-serif;font-size:12pt">
<br>
</div>
</div>
<hr style="display:inline-block;width:98%" tabindex="-1">
<div id="divRplyFwdMsg" dir="ltr"><font face="Calibri, sans-serif"
style="font-size:11pt" color="#000000"><b>From:</b> Healeys
<a class="moz-txt-link-rfc2396E"
href="mailto:healeys-bounces@autox.team.net";><healeys-bounces@autox.team.net></a>
on behalf of Leonard
Berkowitz via Healeys <a class="moz-txt-link-rfc2396E"
href="mailto:healeys@autox.team.net";><healeys@autox.team.net></a><br>
<b>Sent:</b> Wednesday, August 27, 2025 3:50:01 PM<br>
<b>To:</b> <a class="moz-txt-link-abbreviated"
href="mailto:healeys@autox.team.net";>healeys@autox.team.net</a>
<a class="moz-txt-link-rfc2396E"
href="mailto:healeys@autox.team.net";><healeys@autox.team.net></a><br>
<b>Subject:</b> [Healeys] Advice and guidance needed for OD
reinstallation</font>
<div>Â </div>
</div>
<div>
<div
style="font-family:inherit; font-size:inherit; color:inherit;
background-color:transparent">
Hi. All</div>
<div
style="font-family:inherit; font-size:inherit; color:inherit;
background-color:transparent">
I finally figured out how to get the OD out of my BJ7. Now for
getting the new one installed. I found two rings sitting on
the output shaft which I believe are fitted to the adapter
plate. (See pics attached). The problem is going to be how to
keep them in place while maneuvering the new OD into place. I
was thinking of using either white lithium grease or wheel
bearing grease. </div>
<div
style="font-family:inherit; font-size:inherit; color:inherit;
background-color:transparent">
Any suggestions? </div>
<div
style="font-family:inherit; font-size:inherit; color:inherit;
background-color:transparent">
Thank you in advance for any help you can offer. </div>
<div
style="font-family:inherit; font-size:inherit; color:inherit;
background-color:transparent">
<br>
</div>
<div
style="font-family:inherit; font-size:inherit; color:inherit;
background-color:transparent">
Len Berkowitz </div>
</div>
<br>
</blockquote>
</body>
</html>
--------------lKFlS30J0WUeFoSp5l3EkwOb--
--===============4528208051400350220==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys
http://autox.team.net/archive/healeys
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============4528208051400350220==--
|