triumphs
[Top] [All Lists]

Re: [TR] Sparked out

To: "'Mark Hooper'" <mhooper@digiscreen.ca>, <triumphs@autox.team.net>
Subject: Re: [TR] Sparked out
From: "wbeech" <wbeech@flash.net>
Date: Sat, 1 Dec 2007 09:36:47 -0700
--===============0772356313==
Content-Type: text/plain; charset="windows-1250"
Content-Transfer-Encoding: 7bit

I think I have seen 'easy-outs' designed for spark plugs, you might call
around to your local parts stores.

Bill B
'58 TR-3A TS/30766 L
"I love it, she hates it... the car, of course!"
 

-----Original Message-----
From: triumphs-bounces+wbeech=flash.net@autox.team.net
[mailto:triumphs-bounces+wbeech=flash.net@autox.team.net] On Behalf Of Mark
Hooper
Sent: Saturday, December 01, 2007 9:21 AM
To: triumphs@autox.team.net
Subject: [TR] Sparked out

Not an LBC issue, but still I call upon the massed minds of the list. Oh
list, hear me in my agony. My trials and tribulations overwhelm me. Without
your help, surely walking shall await me all the days of the winter.

While getting my winter Buick ready (somewhat late since there is already 4"
of snow on the ground in Montreal) I managed to shear off a spark plug. It
is off right at the edge of the head, so all that is left is the threaded
section that actually screws in. What is the best method of removing this?

Thankfully it is the number one plug (on a transverse V-6) so I can actually
access it to a degree without having to pull the radiator. If it was the
rear side which desperately needs new plugs then it would be game over and
toss the car. The car is just not worth paying somebody to remove the head
and it's too cold in the garage to do more than short-term heating with my
Mr. Heater propane blower.

I can start the car and, of course, it chuffs and hisses, but runs. I am,
however, afraid to drive it far to a shop, as I am assuming that the fuel
injection would rapidly fill the engine bay with an explosive fuel-air
mixture more resembling an IED than a mode of transport.

Is there a known screw extracter size, or a specific device? Left-hand drill
and tap? I'll spend a little on a tool or whatnot, but not too much. The
timing is brilliant since I just made up all new rocker panels and lower
door edges by hand from #16 galvanized and replaced the whole lot.

Mark Hooper
72 TR6
2006 DTS
1991 Buick (mostly dead it seems)
This list supported in part by the Vintage Triumph Register
http://www.vtr.org

http://www.team.net/donate.html

Triumphs@autox.team.net
http://autox.team.net/mailman/listinfo/triumphs

No virus found in this incoming message.
Version: 7.5.503 / Virus Database: 269.16.12/1163 - Release Date: 12/1/2007
12:05 PM
 

Version: 7.5.503 / Virus Database: 269.16.12/1163 - Release Date: 12/1/2007
12:05 PM

--===============0772356313==
Content-Type: text/plain; charset="us-ascii"
MIME-Version: 1.0
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________

Support Team.Net  http://www.team.net/donate.html

This list supported in part by the Vintage Triumph Register
http://www.vtr.org

http://www.team.net/donate.html

Triumphs@autox.team.net
http://autox.team.net/mailman/listinfo/triumphs

--===============0772356313==--

<Prev in Thread] Current Thread [Next in Thread>