MIke,
I am currently testing a prototype Roger Bolick had made by Pertronix on my
71 GT6 MKIII. We are tweaking the placement of the unit as the prototype
required resetting the timing (12 deg) so it was not a direct swap out as it
is on the TR6 model.
One thing I do like about this unit is it all fits under the distributer
cap and fastens down where the points used to go. The wires come with a
grommet that fits the notch on the side of the distrib. so when the cap is
on everything looks proper. No additional boxes or drilling to the firewall
or un-original looking bits.
I will probably run it on my trip to New Orleans on the 22nd. Once the
position gets corrected and wire lenghts/end connectors get tweaked it will
be a great product. Be sure to keep in touch with Roger (rgb@exact.com) on
this one as the "regular" outlets for Ignitors have no clue about GT6 units.
If they can't sell a million thay are not interested. He has also lined up a
unit for the Delco Spitfire distributer as well that is currently running on
a daily driver belonging to Brian at bbyrd@ixc-comm.net.
Regards,
Richard Ceraldi
71 GT6 MKIII KF166L
Austin TX
________________________________________________________
To: triumphs@autox.team.net@INTERNET
From: Mike_A_Gendimenico@ccm.sc.intel.com*RFC-822*@INTERNET on Fri, Mar 7,
1997 8:20 PM
Subject: Re[2]: PERTRONIX Ignitor
Text item:
Do they make one for the GT6 Delco distributors yet?? From what I've heard,
these are much better than the Crane/allison units. Two pieces under the
cap
and two wires to the coil. The dealer I talked to sells both brands and
said he
gets almost zero returns on the Pertronix unit. He gets a lot of returns on
the
Crane units, the connectors and wiring look pretty flimsy and the black box
is a
common failure. If I ever get a TR6 I'll look you up Roger!
Mike
>Does anybody have any experience with a "Pertronix Ignitior"?
I provided the factory with the distributor out of my '70 TR6
for porting their module to the TR6. The was an OEM unit with
dual vacuum advance/retard units, the most complicated of the
TR6 production run.
Interesting aside, I had attempted to purchase one for the TR6
advertised in another "major" vendor's catalog. Upon contacting
the factory I was told "THAT kit will not work properly in the TR6",
though it physically fits... The factory catalog does not list the
Lucas 22D distributor in the application list for that kit...
Hence started my quest to obtain a unit for the TR6.
It does fit entirely inside the distributor, works with and without
a ballast resistor, and greatly helps the starting and high end spark.
The greatest advantage to the EI modules is being immune to the wobble
of the cam shaft due to bushing wear, immune to cam wear, and immune to
breaker plate pivot point wear. These are subtle problems that plague
all the TR6's with more than 50k miles. Impossible to isolate with
normal instruments, but cause a host of run-time erratic timing problems
that prevent the engine from running properly.
The kit you want is LU-166C, this has the clip on the cam-rider
that allows for the variation of cam size problem we encountered.
The factory recommends using the stock coil for most stock applications,
the transistor switched design increases the efficiency of the coil for
a hotter spark over the RPM range. Looking at BRIGHTNESS and CRISPNESS
of the timing light at idle is a sure indicator. I run a 0.035 plug
gap with the Ignitor installed. The 11 to 1 compression engine uses
the Ignitor with Lucas Sport Coil.
Now for the kicker:
1. I currently have a prototype unit for the Spitfire in test
2. I currently have a prototype unit for the GT6 in test
3. I have a case of TR6 Ignitors (LU-166C), $60 plus $3 shipping in US.
Roger Bolick (this is a hobby, don't expect much service)
7205 Valburn Dr.
Austin, TX 78731
512-794-9567
Based on experience so far, I estimate 1 of 3 cars have ignition problems,
wrong/weak coil, coil backwards, vacuum hooked up wrong, etc. If something
else is fouled up, don't expect this to magically fix it!
Text item: External Message Header
The following mail header is for administrative use
and may be ignored unless there are problems.
***IF THERE ARE PROBLEMS SAVE THESE HEADERS***.
but
Subject: Re: PERTRONIX Ignitor
Cc: pficklin@qnis.net
To: triumphs@autox.team.net
From: rgb@exact.com
Date: Fri, 7 Mar 14:50:04 1997
Received: (from root@localhost) by triumph.cs.utah.edu (8.8.3/) id OAA23101
for
triumphs-outgoing; Fri, 7 Mar 1997 14:23:11 -0700 (MST)
Received: from localhost (daemon@localhost) by triumph.cs.utah.edu (8.8.3/)
with
SMTP id OAA23139; Fri, 7 Mar 1997 14:23:17 -0700 (MST)
Received: from triumph.cs.utah.edu by imssc1.sc.intel.com (8.8.4/10.0i); Fri,
7
Mar 1997 21:29:21 GMT
Received: from imssc1.sc.intel.com by ccmgate1.sc.intel.com with smtp
(Smail3.1.28.1 #3) id m0w37A1-000S66a; Fri, 7 Mar 97 13:26 WET
|