tigers
[Top] [All Lists]

Re: [Tigers] Accelerator Pedal Slipping

To: <rfraser@bluefrog.com>, "'John Stithem'" <mai65tai@sonic.net>,
Subject: Re: [Tigers] Accelerator Pedal Slipping
From: "wsamouce" <wsamouce@kc.rr.com>
Date: Thu, 9 Sep 2010 18:34:11 -0500
Thanks to you Ron,

I was a bit unclear in my post.  I cut the groves in the clamping area of
the pedal bracket.  I did not touch the shaft other then cleaning it up.
This, I believe, allows the pedal bracket to bite into the throttle shaft.

I used a Dremel to do the job.

Hope that is a little clearer.

Duke
B382002037

-----Original Message-----
From: Ron Fraser [mailto:rfraser@bluefrog.com]
Sent: Thursday, September 09, 2010 4:54 PM
To: wsamouce@kc.rr.com; 'John Stithem'; tigers@autox.team.net
Subject: RE: [Tigers] Accelerator Pedal Slipping

Duke
        Excellent reply.  I have always just recommended cutting the slot
bigger to get more clamp force.  I did not think about knurling the shaft.
I like that idea.

        Knurling the shaft is the term generally used for making grooves in
the shaft.   Knurling does not cut the metal it rolls the pattern into the
metal.  This work hardens the metal or it should work harden the metal;
which should give a harder and better surface to clamp on.

        You would probably need a gap bed lathe or a manual tool if they
exist for this job.

Ron

-----Original Message-----
From: tigers-bounces@autox.team.net [mailto:tigers-bounces@autox.team.net]
On Behalf Of wsamouce@kc.rr.com
Sent: Thursday, September 09, 2010 3:39 PM
To: John Stithem; tigers@autox.team.net
Subject: Re: [Tigers] Accelerator Pedal Slipping


I had the same issue.  It is fixed now.

If you remove the pedal from the shaft, you will see that there is a cut out
that decreases in size of the opening when you tighten the bolt which crimps
the pedal to the throttle shaft.  Mine was just about completely closed when
tightened.  I cut some material of off one side which allows the opening to
close further.  Additionally I cut groves across the clamping face to make
bteethb that would bite into the shaft.  I also replaced the bolt because
it was bent.  Now a gorilla canbt get the pedal to slip on the shaft.

Also, make sure that the floor stop is there and properly adjusted.  That
way, at WOT, you are not putting undue stress on the pedal and throttle
linkage.

HTH's

Duke
B382002037



---- John Stithem <mai65tai@sonic.net> wrote:
> Anyone have a good way of keeping the accelerator pedal from slipping.
>
> During hard acceleration (autocross racing and Hillclimbs) I find the
> accelerator pedal has slipped at the pinch joint where it is attached
> to
the
> floorboard. I have tried to tighten it and have had to go a small
> Grade 8 bolt (kept snapping the lesser bolts) just to pinch it hard
> enough to get
it
> to work for daily driving. I find after each run while racingI have
> to reach down and pull the pedal back up into the correct position.
>
>
>
> Thanks in advance for any ideas.
>
>
>
> Virginia City Hillclimbs are in 1 = weeks----how many Tigers are
> going?
>
>
>
> John Stithem
> _______________________________________________
> Tigers@autox.team.net
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
http://autox.team.net/mailman/options/tigers/wsamouce@kc.rr.com
_______________________________________________
Tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/tigers/rfraser@bluefrog.com

No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.441 / Virus Database: 271.1.1/3121 - Release Date: 09/09/10
06:34:00
_______________________________________________
Tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

<Prev in Thread] Current Thread [Next in Thread>