tigers
[Top] [All Lists]

Re[4]: New Thread (was REALLY, REALLY SMALL...)

To: bradshaw@utdallas.edu, tigers@autox.team.net, marrone@wco.com,
Subject: Re[4]: New Thread (was REALLY, REALLY SMALL...)
From: LeBrun@hii.hitachi.com
Date: Wed, 26 Jun 96 16:51:46 PST
     Rich;
     
     -Just remember the "racer's" you see doin' the 9.5K + RPM's either 
     have or their sponsor's have deep pockets.They may turn 'em 9K all
     season...betcha' they tear 'em down every week and put in new 
     bearings, etc.? Are you willing to do the same on a high winding 
     TIGER/ALPINE?
     
     Top-fuelers & Funny-cars hit extreme RPM's...they also come to each 
     race with a few extra blocks & complete sets of engine parts.
     
     At the RPM's you're talking about you should go to a roller cam with
     higher spring pressures to avoid valve float, add screw-in studs, etc.
     Who makes what kind of "top-end" stuff for the 215?
     
     Boat racing also uses completely different power and torque 
     requirements than what may be desireable on the street. I've seen MANY
     attempts at wholesale tranplants of racing motors into street cars 
     that couldn't get you from one stoplight to the next without fouling 
     the plugs to an un-runnable condition. Never mind calling all the cops 
     in a 5-mile radius to your location.
     
     Don't mean to "rain on your parade"...I'd hate to see another TIGER/
     ALPINE fan such as yourself sink a lot of money and effort into a 
     "project" that had an undesireable ending.
     
     Hey..go for it, stuff something radical into an ALPINE and make all 
     the naysayers like me eat crow when your'e all finished & blown us 
     into the weeds! Just do enough homework so you have a real comfort 
     level before you start.
     
     One of the individuals affiliated with the SOG in the San Diego area 
     has been putting V-6 Capri engines into ALPINES with a real good 
     success rate. Get in touch with them...they may know somebody who's 
     done different transplants like the 215 into an ALPINE.
     
     
                            Phil


______________________________ Reply Separator _________________________________
Subject: RE: Re[2]: New Thread (was REALLY, REALLY SMALL...)
Author:  "Richard Atherton (Entex)" <a-richat@microsoft.com> at ~INTERNET
Date:    6/26/96 4:23 PM


 Well, in my exploits of trying to do this very thing, I determined that
the Alpine would have to be fitted with a custom made radiator possible 
mounted on the front side of the Bulkhead.  The buick waterpump shaft 
does stick out a ways.  Since cumstom radiators are no stranger to 
Tigers wanting better cooling, the expense is is feasable.  And since 
the Stock Alpine steering is much better than the Tigers, I think this 
is a reasonable trade off.  The Aluminum V-8 powered Alpine would still 
handle better then the Tiger.   In my Opinion.  The Tiger would quicker 
out of the hole (assuming the same gearing) due to its extra torque, but 
the Alpine would pass it by in top speed due to the Higher Revs of the 
215 at 9,500 max RPM (Built for racing using the boat racers specs. 
They turn them 9,000 all season long and 9,500 during the finals at each 
event.!!!).  The Alpine would also be a lot easier on tires (normal 
driving) becuase the stock steering does not scrub the tires like the 
Tiger does.
     
Rich
     
     
>----------
>From:  marrone@wco.com[SMTP:marrone@wco.com] 
>Sent:  Monday, June 24, 1996 11:57 PM
>To:  Keith Bradshaw; tigers@autox.team.net
>Subject:  Re: Re[2]: New Thread (was REALLY, REALLY SMALL...) 
>
>
>
>> As for weight...I could lift the Alpine engine (w/o head) out of the 
>>Alpine, 
>> and set it on a fender before I climbed out....the V-8's even without heads 
>> were very heavy with a thick crank and eight pistons. 
>> 
>> I don't think the Buick V8 was lighter than just about any 4 cylinder 
>>around,
>> except for Pontiac Tempest's 194 c.i. slant four ,which was half of the 
>389 V8.
>
>My info says Tempest slant 4 is 470lbs (yikes!). 
>
>>
>> My guess was the Alpine engine full up was 180 lbs and the V8's full 
>>up were  
>> 300 lbs. 
>
>The word on the street is that the MGBV8 swap results in a lighter car. 
>Figures I have show the Buick 215 at 320lbs and the Leyland 1800 at 
>335.
>The 1800 has a cast head so I wouldn't be surprised if the Alpine mill 
>is a
>bit lighter than the Leyland but its not 155lbs lighter. The engine 
>weight
>list I have is mostly 'mericun 'arn and some race car motors but there 
>are a
>few exotics and imports.  The 215 is lighter than some fours on the 
>list and
>heavier than others but it isn't one sided. 
>
>I'd agree that the 289/302 (at 460lbs) is a nice light, compact 
>package.  In
>a practical sense the Ford has far greater HP potential because of the 
>availability and lower cost of performance goodies (at least here in 
>the
>States).
>
>Could you retain the Alpine steering, as someone suggested, because the 
>lighter aluminum engine is not such a liability far forward in the bay? 
>Those Buick and Rover V8s are pretty long but so are the Fords and 
>Miles got
>a Ford to fit by using electric fans in front of the radiator.  I think 
>the
>only thing for it would be for someone out there to try it and let us 
>all
>know how it goes!
>
>Frank Marrone          MK I Tiger B9471116 
>marrone@wco.com        1966 LTD 
>                       Series I Alpine  (2.3L powered by Ford) 
>                       Yamaha Seca 900
>
>


<Prev in Thread] Current Thread [Next in Thread>