healeys
[Top] [All Lists]

[Healeys] Stator tube wiring loom

Subject: [Healeys] Stator tube wiring loom
From: boyracer466 at gmail.com (richard mayor)
Date: Mon, 5 Mar 2018 19:55:50 -0800
References: <1670068438.10599029.1520212547445.ref@mail.yahoo.com> <1670068438.10599029.1520212547445@mail.yahoo.com> <CAFBXTkKcOLpg9g_6RnuqRaqWidG8-SbSYTK_JsP5_u1Pw1xE9A@mail.gmail.com> <CAJKrNeS5motpwsM3HNi0UnCt8ANLLDH6rJkeKvFB=33-R5Uizw@mail.gmail.com>
What is a "Lantern" spring?

On Mon, Mar 5, 2018 at 6:15 PM, Curtis Arndt <cnaarndt at gmail.com> wrote:

> Alan,
>
> Been there done that.  Typically the old stator tube is so rusty as to
> make messing with this NOT worth my time and effort.  The wires are
> sometimes near impossible to remove. Moss sells a really nice stator tube,
> and the new wiring harness fits down very nicely without having to cut off
> one of the bullets.  What I'm saying is that IF you can get the wires out,
> the inside of the tube will still be a bloody mess.
>
> I know, I just built up a 100M trafficator switch for an owner in
> Arizona.  His stator tube was very rusted and the wires would not budge.
> In the trash it went, and I ordered one from Moss.  And yes, I saved the
> almost impossible to find "Lantern" spring on the stator tube!
>
> Plus, who would want to pt their switch on a rusty old stator tube?
>
> I have not forgotten, just busy.  I'll email you about mailing the battery
> cases to Michael
>
> Cheers,
>
> Curt
>
> On Mon, Mar 5, 2018 at 3:19 PM, Alan Seigrist <healey.nut at gmail.com>
> wrote:
>
>> Maybe give oven cleaner a try?
>>
>> On Sun, Mar 4, 2018 at 8:15 PM, Bert Van Brande <bertvanbrande at yahoo.com>
>> wrote:
>>
>>>
>>> As I am ready to replace the stator wiring loom on the 56 100 BN2, I
>>> find the old loom is completely stuck inside the tube.
>>> I have no wires left on the trafficator end.  Pulling the wire on the
>>> other end, there is no movement and I am afraid I will break the little
>>> that is left from the brittle wires. (not that I need them)
>>>
>>> Any garage tricks to negotiate these 62 year old wires from the tube?  I
>>> already tried WD40 and some modest heat applied to outside of the tube but
>>> no luck yet.
>>>
>>> Bert
>>>
>>> _______________________________________________
>>> Support Team.Net http://www.team.net/donate.html
>>> Suggested annual donation  $12.75
>>> Archive: http://www.team.net/archive
>>> Forums: http://www.team.net/forums
>>>
>>> Healeys at autox.team.net
>>> http://autox.team.net/mailman/listinfo/healeys
>>>
>>> Unsubscribe/Manage: http://autox.team.net/mailman/
>>> options/healeys/healey.nut at gmail.com
>>>
>>>
>>>
>>
>> _______________________________________________
>> Support Team.Net http://www.team.net/donate.html
>> Suggested annual donation  $12.75
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>>
>> Healeys at autox.team.net
>> http://autox.team.net/mailman/listinfo/healeys
>>
>> Unsubscribe/Manage: http://autox.team.net/mailman/
>> options/healeys/cnaarndt at gmail.com
>>
>>
>>
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation  $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage: http://autox.team.net/mailman/
> options/healeys/boyracer466 at gmail.com
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/healeys/attachments/20180305/e9b6ebed/attachment.html>

<Prev in Thread] Current Thread [Next in Thread>