Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Patching\s+an\s+oil\s+pan\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Patching\s+an\s+oil\s+pan\s*$/: 7 ]

Total 7 documents matching your query.

1. Patching an oil pan (score: 1): Author: Don Malling <dmallin@attglobal.net>; Date: Tue, 02 Aug 2005 23:44:04 -0400; Anyone have any ideas on how to patch a rust hole in an oil pan w/o removing the oil pan. It's on a 93 ranger pickup and the manual says I have to lift the engine up a few inches and remove portions; /html/shop-talk/2005-08/msg00003.html (7,169 bytes)
2. Re: Patching an oil pan (score: 1): Author: Paul Parkanzky <parkanz1@msu.edu>; Date: Wed, 3 Aug 2005 00:22:39 -0400; I have successfully used JB Weld for this on a car that we couldn't buy a new oil pan for. Drain the oil. Clean it up the best you can. ~Paul; /html/shop-talk/2005-08/msg00004.html (7,350 bytes)
3. RE: Patching an oil pan (score: 1): Author: "Gerald Brazil" <gerrybraz@cablespeed.com>; Date: Wed, 3 Aug 2005 09:45:59 -0400; How bad is the hole? If just a pin hole, like from a rock, I have had success by using a large short sheet metal screw, like a # 10 or #12 and putting a small O ring under it and screwing it in tight; /html/shop-talk/2005-08/msg00006.html (7,812 bytes)
4. Re: Patching an oil pan (score: 1): Author: Don Malling <dmallin@attglobal.net>; Date: Wed, 03 Aug 2005 09:48:12 -0400; Thanks to all who responded. I will try the JB weld. Suggestions on what to use to clean the outside of the oil pan? Maybe denatured alcohol, Laquer thinner, POR-15 Marine Clean, brake cleaner? What; /html/shop-talk/2005-08/msg00007.html (7,155 bytes)
5. Re: Patching an oil pan (score: 1): Author: "Bill Engle, Sr." <whesr@iglou.com>; Date: Wed, 03 Aug 2005 10:33:41 -0400; Just make sure you get as much oil off as possible. I would use the five Bill; /html/shop-talk/2005-08/msg00008.html (7,260 bytes)
6. Re: Patching an oil pan (score: 1): Author: Wayne <wmc_st@xxiii.com>; Date: Wed, 03 Aug 2005 10:45:17 -0400; Pop-rivet a metal patch on with some JB Weld slathered on the area??? Any real welding would not go well with the residual oil. -Wayne; /html/shop-talk/2005-08/msg00009.html (7,243 bytes)
7. Re: Patching an oil pan (score: 1): Author: "Bob Spidell" <bspidell@comcast.net>; Date: Wed, 3 Aug 2005 08:12:37 -0700; If the hole is on the bottom of the pan you might have trouble getting liquid epoxy to stay in place. I've had success patching mufflers with the stick epoxy-steel stuff (JB Weld makes it, too). Sand; /html/shop-talk/2005-08/msg00010.html (8,056 bytes)

Current List: 1 - 7
Page: [1]