datsun-roadsters
[Top] [All Lists]

Re: [Roadsters] Rear Wheel Studs

To: <bhollan4@tampabay.rr.com>, <datsun-roadsters@autox.team.net>
Subject: Re: [Roadsters] Rear Wheel Studs
From: Stephen Holst <stephen.holst@randrglobal.com>
Date: Sun, 20 May 2012 09:45:30 -0400
Delivered-to: mharc@autox.team.net
Delivered-to: datsun-roadsters@autox.team.net
In-reply-to: <20120520015406.EJPWB.104708.root@hrndva-web07-z02>
List-archive: <http://autox.team.net/pipermail/datsun-roadsters>
List-help: <mailto:datsun-roadsters-request@autox.team.net?subject=help>
List-id: Datsun Roadster discussion <datsun-roadsters.autox.team.net>
List-post: <mailto:datsun-roadsters@autox.team.net>
List-subscribe: <http://autox.team.net/mailman/listinfo/datsun-roadsters>, <mailto:datsun-roadsters-request@autox.team.net?subject=subscribe>
List-unsubscribe: <http://autox.team.net/mailman/options/datsun-roadsters>, <mailto:datsun-roadsters-request@autox.team.net?subject=unsubscribe>
Sender: datsun-roadsters-bounces@autox.team.net
Thread-index: Ac02jtH+oY7wSvFEbEuknfkd5JTwkQ==
Thread-topic: [Roadsters] Rear Wheel Studs
User-agent: Microsoft-Entourage/12.32.0.111121
On the otherhand "when was the last time you re-greased the wheel bearings?"
After 40-50 years it gets pretty dry.
Steve


On 5/19/12 9:54 PM, "bhollan4@tampabay.rr.com" <bhollan4@tampabay.rr.com>
wrote:

> Actually, there is another way.  If you don't mind drilling an appropriately
> sized hole in the backing plate you can insert new, longer studs through the
> hole.  I used that technique to put long ARP studs on my car - then used a lug
> nut to "pull" the stud into the flange.  If you're careful, you can drill the
> hole in the right spot and then use a rubber plug to seal it back up if so
> desired.
> Doing it this way doesn't require pulling the collar off of the axle which is
> a PITA.
> Good luck,
> Brian
> 69 2000
> Tampa FL
> 
> 
> ---- Graeme Suckling <graemes@internode.on.net> wrote:
>> I think you'll find that the rear axle has to be extracted slightly to
>> get the old ones out as well as re-insert the new.
>> This is a definite if you are wanting to instal longer wheel studs.
>> 
>> Regards,
>> Graeme Suckling
>> http://tinyurl.com/6n5aza
>> Adelaide
>> South Australia.
>> 
>> 
>> On 20/05/2012 6:09 AM, Gary and Cindy Ault wrote:
>>> Has anyone on the List replaced rear wheel studs?  If so, do the axles need
>>> to
>>> be removed to change them?  To the extent that it makes a difference, the
>>> car
>>> in question is a '67-1/2.  Thanks.
>>> 
>>> Gary
>>> ________________________________________
>>> 
>>> datsun-roadsters@autox.team.net
>>> 
>>> Donate: http://www.team.net/donate.html
>>> Archive: http://www.team.net/archive
>>> Forums: http://www.team.net/forums
>>> Unsubscribe: 
>>> http://autox.team.net/mailman/options/datsun-roadsters/graemes@internode.on.
>>> net
>> ________________________________________
>> 
>> datsun-roadsters@autox.team.net
>> 
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe: 
>> http://autox.team.net/mailman/options/datsun-roadsters/bhollan4@tampabay.rr.c
>> om
> ________________________________________
> 
> datsun-roadsters@autox.team.net
> 
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe: 
> http://autox.team.net/mailman/options/datsun-roadsters/stephen.holst@randrglob
> al.com
________________________________________

datsun-roadsters@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: 
http://autox.team.net/mailman/options/datsun-roadsters/mharc@autox.team.net


<Prev in Thread] Current Thread [Next in Thread>