BTW, Don't use a jumper unless you put a fuse inline.
Mike
----- Original Message -----
From: "Datsun_Sports" <Datsun_Sports@hotmail.com>
To: "Datsun Forum" <datsun-roadsters@autox.team.net>; "datsunmike"
<datsunmike@nyc.rr.com>
Sent: Friday, June 21, 2002 6:35 PM
Subject: Re: ignition electrical questions for a 1600 early 67
> hi,
>
> I used a meter and found that im getting 12 volts all the way to the fuse
> box. I double checked the wiring and it looks good. will a bad ammeter
cause
> this? does a jumper wire bypass the meter? I have the dash out and
> everything is hanging down. am I missing something else that needs to be
> grounded or hooked up? I have the fuel gauge, ammeter and oil gauge. the
> fuel gauge registers when I use the jumper.
>
> thx for the help., I appreciate it.
>
> mike
> ----- Original Message -----
> From: "datsunmike" <datsunmike@nyc.rr.com>
> To: "Datsun_Sports" <Datsun_Sports@hotmail.com>
> Sent: Friday, June 21, 2002 2:50 PM
> Subject: Re: ignition electrical questions for a 1600 early 67
>
>
> > It shouldn't make a difference too much although the resistance can
vary.
> > Either end is OK but it doesn't sound as if power is flowing through the
> > ballast resistor. Are you getting current to the resistor? Is the wire
> that
> > connects from the harness to the resistor live? Check there for voltage.
> >
> > Run a lead from the battery as you did before to the resistor. If that
> > doesn't start the car the resistor may be defective. What else is new :(
> >
> >
> > ----- Original Message -----
> > From: "Datsun_Sports" <Datsun_Sports@hotmail.com>
> > To: "datsunmike" <datsunmike@nyc.rr.com>
> > Sent: Friday, June 21, 2002 5:40 PM
> > Subject: Re: ignition electrical questions for a 1600 early 67
> >
> >
> > > hi,
> > >
> > > I bought one at checker. they said that it would not make a difference
> if
> > it
> > > was not a stock ballast. I was told it is to limit interference. does
it
> > > matter what end is plugged into the coil side? it looks the same on
each
> > > end.
> > >
> > > thx,
> > >
> > > mike
> > > ----- Original Message -----
> > > From: "datsunmike" <datsunmike@nyc.rr.com>
> > > To: "Datsun_Sports" <Datsun_Sports@hotmail.com>; "Datsun Forum"
> > > <datsun-roadsters@autox.team.net>
> > > Sent: Friday, June 21, 2002 2:01 PM
> > > Subject: Re: ignition electrical questions for a 1600 early 67
> > >
> > >
> > > > Check the ballast resistor to make sure it works.
> > > >
> > > > Mike
> > > >
> > > > ----- Original Message -----
> > > > From: "Datsun_Sports" <Datsun_Sports@hotmail.com>
> > > > To: "Datsun Forum" <datsun-roadsters@autox.team.net>
> > > > Sent: Friday, June 21, 2002 4:16 PM
> > > > Subject: ignition electrical questions for a 1600 early 67
> > > >
> > > >
> > > > > Hi,
> > > > >
> > > > > it looks like I have everything hooked up for the ignition
properly.
> I
> > =
> > > > > also installed a ballast resistor. the car will turn over but will
> not
> > =
> > > > > start. it does not appear to betting any spark. when I run a
jumper
> > from
> > > =
> > > > > + on the battery to the + on the coil it starts right up. any
ideas?
> > > > >
> > > > > thx for the help,
> > > > >
> > > > > mike
> > > > >
> > > > > [demime 0.97c removed an attachment of type image/jpeg which had a
> > name
> > > of
> > > > Fishing.jpg]
> > > > >
> > > > > /// datsun-roadsters@autox.team.net mailing list
> > > > > /// Send admin requests to majordomo@autox.team.net or go to
> > > > > /// http://www.team.net/cgi-bin/majorcool
> > > > > /// Send list postings to datsun-roadsters@autox.team.net
>
> /// datsun-roadsters@autox.team.net mailing list
> /// Send admin requests to majordomo@autox.team.net or go to
> /// http://www.team.net/cgi-bin/majorcool
> /// Send list postings to datsun-roadsters@autox.team.net
/// datsun-roadsters@autox.team.net mailing list
|