datsun-roadsters
[Top] [All Lists]

Re: Shock Installation questions...help needed

To: "Vicki Burrows" <gregnvicki@earthlink.net>,
Subject: Re: Shock Installation questions...help needed
From: "datsunmike" <datsunmike@nyc.rr.com>
Date: Wed, 5 Jun 2002 06:31:35 -0400
Impact Guns Rule!!!!!

One of the best devices ever invented for working on cars, especially old
ones. I don't know how I lived w/o it. Actually I cursed a lot before.

Mike

----- Original Message -----
From: "Vicki Burrows" <gregnvicki@earthlink.net>
To: "David Totah" <dstotah@hotmail.com>
Cc: <datsun-roadsters@autox.team.net>
Sent: Wednesday, June 05, 2002 12:31 AM
Subject: Re: Shock Installation questions...help needed


> I too remember spending hours under my car recently taking off those #@$%#
lock
> nuts one tick at a time.  I was sooooo pissed off that I actually sprayed
them
> in starting fluid and burned the plastic out of them. There was NO WAY I
was
> gonna put them back on one tick at a time again.  Then I used loctite to
hold
> them.  They went on much easier.  I think after that I went out and bought
some
> racheting wrenches... good stuff to have.  Regarding the shock and
compression,
> I don't think you will have too much trouble... just make sure that you
are
> ready to aim the shock as it expands and you might get lucky and hit the
mount.
> Good luck!
> Greg Burrows
>
> David Totah wrote:
>
> > Last night I printed the installation pages from the 311s.org site on
how to
> > install front and rear shocks.  While it seemed easy enough, I quickly
found
> > out that it was in for a long night of work.  I spent 3 hours getting
the
> > lock nut off the fram bolt at the upper fastening of the old shock.
> > I placed the new shock on the upper bolt, but an thinking of replacing
the
> > lock nut with a regular nut and a lock washer.  Any reasons I shouldn't
do
> > this.
> >
> > Secondly, The new shock is already compressed.  I am planning on
securing
> > the upper part first and then cutting the compressing strap that is over
the
> > entire shock.  How hard is it going to be to compress this new high
pressure
> > KYB gas shock to the point that I can place it in the old suspension
hole
> > and then secure the shock?
> > Any tips on compressing the shock?  I think someone mentioned that they
> > wrapped the shock with duct tape to keep it compressed.
> >
> > If anyone has a couple free evenings to help me out this week, I will
bring
> > out the Bar-B-Q grill, season a couple of steaks/burgers/you name it,
and I
> > will cook it.
> >
> > I would appreciate any tips or hints.
> >
> > Thanks,
> > Dave
> > 69' SRL311
> >
> > _________________________________________________________________
> >
> > ///  datsun-roadsters@autox.team.net mailing list
> > ///  Send admin requests to majordomo@autox.team.net  or go to
> > ///  http://www.team.net/cgi-bin/majorcool
> > ///  Send list postings to datsun-roadsters@autox.team.net
>
> ///  datsun-roadsters@autox.team.net mailing list
> ///  Send admin requests to majordomo@autox.team.net  or go to
> ///  http://www.team.net/cgi-bin/majorcool
> ///  Send list postings to datsun-roadsters@autox.team.net

///  datsun-roadsters@autox.team.net mailing list


<Prev in Thread] Current Thread [Next in Thread>