Torque is 10lbs.
----- Original Message -----
From: "Gary McCormick" <svgkm@halley.ca.essd.northgrum.com>
To: "Stan Chernoff" <az589@lafn.org>
Cc: "Daniel Neuman" <dneuman@quark.sfsu.edu>;
<datsun-roadsters@autox.team.net>
Sent: Thursday, May 02, 2002 12:29 PM
Subject: Re: 2000 intake manifold question
> I don't have any reference material at hand to look up the torque values,
but the sequence
> is from inside to outside, starting in the center and working outwards
alternating to the
> left and right of center; the torque values should be stepped up, also,
taking it in 2,
> maybe 3, steps depending upon the final value.
>
> This is a general rule for securing a manifold, or any component that
secured by threaded
> fasteners in a generally rectangular pattern, especially a component which
must seal
> against its mating part. Working inside to outside, alternately left and
right, and
> stepping up the torque will prevent distortion. A cylinder head is another
example of a
> component which should be torqued up in this fashion.
>
> Gary McCormick
> San Jose, CA
> '70 2000 SRL311-13291
>
> Stan Chernoff wrote:
>
> > Gary
> >
> > What are the right values and what is the right sequence?
> >
> > ============
> >
> > At 08:32 AM 5/2/02 -0700, Gary McCormick wrote:
> > >To the right values, in the right sequence.
> > >
> > >Gary McCormick
> > >San Jose, CA
> > >'70 2000 SRL311-13291
> > >
> > >Daniel Neuman wrote:
> > >
> > >> What does 'torqued right' mean exactly?
> > >> Daniel 69 2000
> > >> Oakland CA
> > >>
> > >> > Sidney
> > >> > I use a little around the water inlet ports only if I suspect a
leak. The
> > >> > rest will seal on its own if torqued right.
> > >> > Mike Koken
> > >> > colo. springs
> > >> > ----- Original Message -----
> > >> > From: "sidney raper" <spl310@hotmail.com>
> > >> > To: <datsun-roadsters@autox.team.net>
> > >> > Sent: Tuesday, April 30, 2002 7:22 PM
> > >> > Subject: 2000 intake manifold question
> > >> >
> > >> >
> > >> > > Is there any recommendation regarding gasket sealant on the
> > intake/exhaust
> > >> > > manifold gasket (Nissan) on the 2000?
> > >> > >
> > >> > >
> > >> > >
> > >> > > Sidney Raper
> > >> > > 1964 1500
> > >> > > 1967 SRL311 00060
> > >> > > 1967 SRL311 00076
> > >> > > Jacksonville Florida
> > >> > > http://www.geocities.com/roadsternut/index.html
> > >> > >
> > >> > >
> > >> > >
> > >> > > _________________________________________________________________
> > >> > > Chat with friends online, try MSN Messenger:
http://messenger.msn.com
> > >> > >
> > >> > > /// datsun-roadsters@autox.team.net mailing list
> > >> > > /// Send admin requests to majordomo@autox.team.net or go to
> > >> > > /// http://www.team.net/cgi-bin/majorcool
> > >> > > /// Send list postings to datsun-roadsters@autox.team.net
> > >> >
> > >> > /// datsun-roadsters@autox.team.net mailing list
> > >> > /// Send admin requests to majordomo@autox.team.net or go to
> > >> > /// http://www.team.net/cgi-bin/majorcool
> > >> > /// Send list postings to datsun-roadsters@autox.team.net
> > >>
> > >> /// datsun-roadsters@autox.team.net mailing list
> > >> /// Send admin requests to majordomo@autox.team.net or go to
> > >> /// http://www.team.net/cgi-bin/majorcool
> > >> /// Send list postings to datsun-roadsters@autox.team.net
> > >
> > >/// datsun-roadsters@autox.team.net mailing list
> > >/// Send admin requests to majordomo@autox.team.net or go to
> > >/// http://www.team.net/cgi-bin/majorcool
> > >/// Send list postings to datsun-roadsters@autox.team.net
> >
> > /// datsun-roadsters@autox.team.net mailing list
> > /// Send admin requests to majordomo@autox.team.net or go to
> > /// http://www.team.net/cgi-bin/majorcool
> > /// Send list postings to datsun-roadsters@autox.team.net
>
> /// datsun-roadsters@autox.team.net mailing list
> /// Send admin requests to majordomo@autox.team.net or go to
> /// http://www.team.net/cgi-bin/majorcool
> /// Send list postings to datsun-roadsters@autox.team.net
/// datsun-roadsters@autox.team.net mailing list
|