[TR] TR2 sill / bulkhead sealing
Guy Huggins
guy.huggins at icloud.com
Wed Nov 10 07:50:52 MST 2021
When I restored my car, I had the same question about rust developing in enclosed areas, especially the insides of the chassis.
I ended up creating a “soup” of melted paraffin wax and linseed oil, and injecting it.
The linseed oil keeps the wax from hardening all the way, and ends up like a slush.
Kind Regards,
Guy D. Huggins
guy.huggins at icloud.com
817.454.6415
On Nov 10, 2021, at 5:15 AM, Alan & Lyn Dunscombe <dunscomb at chch.planet.org.nz> wrote:
Hi all
Finally after 40 years driving I am getting the sills & floors on my TR2 replaced, currently at the panel beaters having them welded in. So my question is:-
How to deal with the dirt & moisture trap made by the "box" enclosed by the bulkhead & sealing plate at the front, the 'A' pillar at the back, the sill & front guard (fender in USA) at the bottom, & the rear of the inner guard etc at the top.
We all know that the factory sealing plate & rubber seals at the front are meant to stop the road dirt & moisture getting in, but don't do it very well. Then when it rains the water comes in between the side of the bonnet (hood in USA) & the front guards onto the top of the inner guard (fender), plus at the rear end of the bonnet it runs down from the gutter at the front of the bulkhead into the gap at the rear of the inner guard which is cleverly angled so that all this water drips off the back end into the above mentioned "box" enclosure where it combines with the road dirt etc and eventually rots out the front of the sill and the side kick panel in the cockpit & then the front of the floors.
General consensus seem to be that we should remove the bulkhead sealing plates each year and clean out all this accumulated 'crud' and dry out this area before replacing them.
Has anyone come up with a way of draining this area so it doesn't stay damp?
What is the consensus on the best treatment of this front part of the sill and bottom of the inner side of the guard etc. to stop rust attacking it?
All suggestions gratefully received.
cheers,
stay safe,
Alan TS3612
AW & LJ Dunscombe
New Zealand
On 10/11/2021 8:00 a.m., triumphs-request at autox.team.net <mailto:triumphs-request at autox.team.net> wrote:
>
> Send Triumphs mailing list submissions to
> triumphs at autox.team.net <mailto:triumphs at autox.team.net>
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://autox.team.net/mailman/listinfo/triumphs <http://autox.team.net/mailman/listinfo/triumphs>
> or, via email, send a message with subject or body 'help' to
> triumphs-request at autox.team.net <mailto:triumphs-request at autox.team.net>
>
> You can reach the person managing the list at
> triumphs-owner at autox.team.net <mailto:triumphs-owner at autox.team.net>
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of Triumphs digest..."
>
>
> Today's Topics:
>
> 1. TR4A Pulley Dimensions (Guy Huggins)
> 2. Re: TR4A Pulley Dimensions (David Friedlander)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Mon, 8 Nov 2021 15:41:07 -0600
> From: Guy Huggins <guy.huggins at icloud.com> <mailto:guy.huggins at icloud.com>
> To: Triumph Mailing List <triumphs at autox.team.net> <mailto:triumphs at autox.team.net>
> Subject: [TR] TR4A Pulley Dimensions
> Message-ID: <89B5ABD9-F206-4294-89E2-3389134F155B at icloud.com> <mailto:89B5ABD9-F206-4294-89E2-3389134F155B at icloud.com>
> Content-Type: text/plain; charset=utf-8
>
> Listers,
>
> Does anyone know the dimensions of the two-part crankshaft pulley for the TR4A?
> Mine is attached, and my calipers won?t open enough to measure the diameter.
>
> I am looking to determine the circumference, in order to make timing marks for when I start putting everything back together after the head gasket work.
>
>
> Cheers,
>
> Guy D. Huggins
> 1965 Triumph TR4A
> CTC 63569LO
>
>
>
>
>
> ------------------------------
>
> Message: 2
> Date: Mon, 8 Nov 2021 19:48:03 -0500
> From: David Friedlander <forzion7 at gmail.com> <mailto:forzion7 at gmail.com>
> To: Guy Huggins <guy.huggins at icloud.com> <mailto:guy.huggins at icloud.com>
> Cc: Triumph Mailing List <triumphs at autox.team.net> <mailto:triumphs at autox.team.net>
> Subject: Re: [TR] TR4A Pulley Dimensions
> Message-ID:
> <CAJ1eQwj_n+1MMi02VuZgo0F1y5U3Ao7RzeOq+GBUh_j2-ii6QA at mail.gmail.com> <mailto:CAJ1eQwj_n+1MMi02VuZgo0F1y5U3Ao7RzeOq+GBUh_j2-ii6QA at mail.gmail.com>
> Content-Type: text/plain; charset="utf-8"
>
> Guy;
>
> If it's the same diameter as the pulley on the TR3A then
> the diameter is 5.5 inches. Ten degrees BTDC can be
> marked at 1/2" from the pulley TDC timing mark.
>
> Dave
>
>
> On Mon, Nov 8, 2021 at 4:43 PM Guy Huggins <guy.huggins at icloud.com> <mailto:guy.huggins at icloud.com> wrote:
>
>
>> Listers,
>>
>> Does anyone know the dimensions of the two-part crankshaft pulley for the
>> TR4A?
>> Mine is attached, and my calipers won?t open enough to measure the
>> diameter.
>>
>> I am looking to determine the circumference, in order to make timing marks
>> for when I start putting everything back together after the head gasket
>> work.
>>
>>
>> Cheers,
>>
>> Guy D. Huggins
>> 1965 Triumph TR4A
>> CTC 63569LO
>>
>>
>>
>> ** triumphs at autox.team.net <mailto:triumphs at autox.team.net> **
>>
>> Donate: http://www.team.net/donate.html <http://www.team.net/donate.html>
>> Archive: http://www.team.net/pipermail/triumphs <http://www.team.net/pipermail/triumphs>
>> http://www.team.net/archive <http://www.team.net/archive>
>>
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/triumphs/forzion7@gmail.com <http://autox.team.net/mailman/options/triumphs/forzion7@gmail.com>
>>
>>
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://autox.team.net/pipermail/triumphs/attachments/20211108/86de236b/attachment-0001.htm> <http://autox.team.net/pipermail/triumphs/attachments/20211108/86de236b/attachment-0001.htm>
>
> ------------------------------
>
> Subject: Digest Footer
>
> _______________________________________________
>
> Triumphs mailing list
> Triumphs at autox.team.net <mailto:Triumphs at autox.team.net>
> http://autox.team.net/mailman/listinfo/triumphs <http://autox.team.net/mailman/listinfo/triumphs>
>
>
> ------------------------------
>
> End of Triumphs Digest, Vol 14, Issue 234
> *****************************************
>
>
>
** triumphs at autox.team.net <mailto:triumphs at autox.team.net> **
Donate: http://www.team.net/donate.html <http://www.team.net/donate.html>
Archive: http://www.team.net/pipermail/triumphs <http://www.team.net/pipermail/triumphs> http://www.team.net/archive <http://www.team.net/archive>
Unsubscribe/Manage: http://autox.team.net/mailman/options/triumphs/guy.huggins@icloud.com <http://autox.team.net/mailman/options/triumphs/guy.huggins@icloud.com>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/triumphs/attachments/20211110/3ca999d1/attachment.htm>
More information about the Triumphs
mailing list