[TR] Front Pullet Hub Removal

Jim Henningsen trguy75 at gmail.com
Mon Jul 19 12:48:41 MDT 2021


Thanks.  Pulled cover off and chain and tensioner look really clean.  Definitely have been replaced.  Also evidenced by two new grade 8 bolts attaching fan hub extension.  Chain is also tight so I will leave alone.  

Cheers,

Jim 

 

From: DAVID MASSEY <dave1massey at cs.com> 
Sent: Monday, July 19, 2021 12:42 PM
To: trguy75 at gmail.com; deruiterville at hotmail.com
Cc: triumphs at autox.team.net
Subject: Re: [TR] Front Pullet Hub Removal

 

Chains stretch.  If there is significant slop in the chain you should replace it.  It will make the engine quieter if nothing else.  

 

Dave 

 

 

-----Original Message-----
From: Jim Henningsen <trguy75 at gmail.com <mailto:trguy75 at gmail.com> >
To: 'Randy and Valerie DeRuiter' <deruiterville at hotmail.com <mailto:deruiterville at hotmail.com> >
Cc: 'TR List' <triumphs at autox.team.net <mailto:triumphs at autox.team.net> >
Sent: Mon, Jul 19, 2021 11:22 am
Subject: Re: [TR] Front Pullet Hub Removal

Yes it does and thanks.  Successfully removed it this morning with a puller.  Next up, remove the timing cover and replace oil seal and gasket.  

Any thoughts from the list on what to look for when inspecting the timing chain?  I think it was changed by the previous owner who had the car 45 years but cant confirm.  
Thanks,
Jim 


-----Original Message-----
From: Randy and Valerie DeRuiter <deruiterville at hotmail.com <mailto:deruiterville at hotmail.com> > 
Sent: Monday, July 19, 2021 11:37 AM
To: Jim Henningsen <trguy75 at gmail.com <mailto:trguy75 at gmail.com> >
Cc: TR List <triumphs at autox.team.net <mailto:triumphs at autox.team.net> >
Subject: Re: [TR] Front Pullet Hub Removal

Jim- to avoid bending anything I usually leave the fan extension on and I unthread the dog bolt slightly.  Then I use a puller against the lip of the fan extension and the dog bolt.  This will move it probably by 1/2 inch.  If the hub is still firmly stuck, I replace the dog bolt with a thinner bit longer bolt and pull against it until the hub clears its key.

Hope that makes sense
Randy

Sent from my iPhone

> On Jul 18, 2021, at 6:57 PM, Jim Henningsen <trguy75 at gmail.com <mailto:trguy75 at gmail.com> > wrote:
> 
> List:
> Converting my 67 4A over to the Bastuck narrow fan belt kit. This kit
> retains the fan extension tube and fan.  I have the radiator out and fan
> blade and fan extension removed.  I have the stock pulley at the top 
> dead center position (hole at the top).  Have not removed one of these before.
> Any tips on removing would be greatly appreciated.  I still have the 
> cross tube and was hoping it could be removed while that is still installed.
> Thanks in advance!
> Jim henningsen
> Ocala, FL
> 61 3A
> 67 4A
> 75 6
> 81 8
> 
> ** triumphs at autox.team.net <mailto:triumphs at autox.team.net>  **
> 
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/triumphs  <http://www.team.net/pipermail/triumphs> 
> http://www.team.net/archive
> 
> Unsubscribe/Manage: 
> http://autox.team.net/mailman/options/triumphs/deruiterville@hotmail.c
> om

** triumphs at autox.team.net <mailto:triumphs at autox.team.net>  **

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/pipermail/triumphs  <http://www.team.net/pipermail/triumphs> http://www.team.net/archive

Unsubscribe/Manage: http://autox.team.net/mailman/options/triumphs/dave1massey@cs.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/triumphs/attachments/20210719/b4a7592b/attachment.htm>


More information about the Triumphs mailing list