[Tigers] Rear Sway Bar

[Michael Wood]

I wish Dale still had some of those springs for sale!! I talked to him about making more, but his guy went out of business. Mike


-----Original Message-----
From: GARY WINBLAD <garywinblad at comcast.net>
To: jim <jim at island.net>; jim via Tigers <tigers at autox.team.net>; daniel doornbos <dan_doornbos at hotmail.com>
Sent: Thu, Sep 30, 2021 1:09 pm
Subject: Re: [Tigers] Rear Sway Bar

  Jim,   Nice installation!   My analysis is get rid of that stock panhard rod.   Put your shocks on full soft and drive down the freeway.  As you go over slight dips an bumps the rear end will steer the Tiger   downright dangerously.  The stock rod is too short and is mounted not parallel to the ground.   To get the stability back in the rear axle you get some springs with small bushings in the front, I got Dale's springs.   SO much better!   Gary   
  
  On 09/30/2021 2:45 PM jim via Tigers <tigers at autox.team.net> wrote:   
   
   
My car came with a home made 1 1/8” front bar so understeered a lot!  I got an addco rear bar but couldn’t figure out how to mount it so I made my own… mounted in front of the rear end and welded a couple tabs on the side of the plate that the u-bolts go through to hold the lower links. The brackets that I made are very strong  ( 6-3/8” bolts per side) and you’d have to rip the car apart before they would let go!  The calculations say it’s only giving me about 75 lbs./inch with 12” arms and a 34”  ¾” solid bar. It makes quite a difference which between the 3  adjustment holes though. I got the bar. arms etc. from Speedway Engineering ( $200 ) and it was pretty reasonable actually… biggest job was to make the brackets!
 
On another note, I have the ‘Stock’ mounting for my panhard rod …I’m not sure if it’s causing this ( I think likely ) but I notice in hard cornering that the car will understeer some on left turns and oversteer on right turns !! Anyone else notice that effect ? I have quite a bit of ‘ackerman’ correction in the front suspension also
 

 
Jim
 
B382000446
 


 


 


   
From: Tigers <tigers-bounces at autox.team.net> On Behalf Of daniel doornbos via Tigers
Sent: Thursday, September 30, 2021 10:24 AM
To: tigers at autox.team.net
Subject: [Tigers] Rear Sway Bar
   


  
I couldn't find an aftermarket rear sway bar for the Tiger I liked.  And I looked at the DIY weld kits.  But after reading and finding that bending and welding impact metal spring rate and you should temper the bar post fabrication to get it to work correctly.  For the rear end and space I needed to put in bends around the pumpkin and linkages.    
   
 
   
I do recognize that welded options will also work well.  My Mustang II front end from Mike H has a welded bar.  But for the rear packaging, I needed too many bends and couldn't locate a straight bar type in the space.   In the end, I went with a custom-built from https://www.carolinaswaybar.com/ It was a premium price but they were great to work with. 
   
 
   
Maybe in the next decade I'll get enough motivation to finish and drive the car to see how good my choices were.
   
 
   
dan
    
|   

  |   
Carolina Swaybar Manufacturing - Newland, NC
   
Carolina Swaybar Manufacturing designs and creates the best swaybars on the market today. Industry leading R&D, commitment to customer satisfaction.
   
www.carolinaswaybar.com
  |

   


 _______________________________________________ 
 
tigers at autox.team.net 
 
Donate: http://www.team.net/donate.html 
Archive: http://www.team.net/pipermail/tigers http://autox.team.net/archive 
 
Unsubscribe: http://autox.team.net/mailman/options/tigers/garywinblad@comcast.net 
 
 
 
 _______________________________________________

tigers at autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/pipermail/tigers http://autox.team.net/archive

Unsubscribe: http://autox.team.net/mailman/options/tigers/mwood24020@aol.com


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/tigers/attachments/20211001/26766a6e/attachment-0001.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 1951791 bytes
Desc: not available
URL: <http://autox.team.net/pipermail/tigers/attachments/20211001/26766a6e/attachment-0001.jpg>