[Tigers] inside door parts questions

[Gary]

I would assume that pictured little rubber
piece goes inside the handle before you
put it in the post.
You must get the pin centralized in the
handle, then the spring can push the ring
out.  The ring keeps the pin from falling out.
I have used cut off nails when I have lost the
pins.
Gary

Sent from my iPhone

> On May 27, 2020, at 9:01 PM, Derek Daily via Tigers <tigers at autox.team.net> wrote:
> 
> Hmmm, i was just going through door reassembly this weekend. Where would the rubber "sleeve" go? In my case, early MKIA ...000428, the handles are snug over the male post. In fact, as one of those original fixing pins has gone missing, i attempted to use plumbing tape over the post prior to replacing the handle pin and the handle could not slide over the thin tape. No way a rubber sleeve would work on this car (unless im misunderstanding Placement location..). 
> 
> FWIW, i have three donuts per side. Two on door latch post One on window crank. However, I can state no knowledge of original location. 
> 
> Also: while we on on this Door topic, about the escutcheon with chrome ring and spring to mate from door card to "base" of lever after reattaching... those suck. On most i have the chrome pushed in to eacutcheon far enough to allow the pin to be inserted and no way to pull chrome out once handle is connected. Even if i did, the chrome would never slide back in to allow handle pin removal Ever again. All hardware here including card are original. 
> 
> Lets see if i can attach...
> 
> 
> <image1.jpeg>
> 
> 
> 
> Derek Daily
> dtdaily at yahoo.com
> 
>>> On May 27, 2020, at 6:09 PM, michael king <michael.s.king at gmail.com> wrote:
>>> 
>> Sorry photo didn't attach...the anti rattle rubber.
>> 
>>> On Thu., 28 May 2020, 11:08 michael king, <michael.s.king at gmail.com> wrote:
>>> Jim..  I havent got access to the manuals in front of me... But.. The doors have the felt spacers on the winder and handle. They also had a rubber spacer sleeve that was used on the handles that goes over the shaft and the handle slips over those so stop them rattling.. Maybe thats what you are looking at?
>>> 
>>> Pic attached
>>> 
>>> 
>>> 
>>>> On Thu., 28 May 2020, 08:59 James Armstrong via Tigers, <tigers at autox.team.net> wrote:
>>>> Hello,
>>>> 
>>>> 
>>>> In putting my door back together, I have a few questions:
>>>> 1) are there two felt donuts, one on the window winder shaft (shown but not called out in Alpine parts manual) and is there another on the door opener shaft?
>>>> 
>>>> 2) what the heck are part #s YX  Illus. B # s  98 and 98/1 inside of door around the door opening shaft?
>>>> Also in the Alpine parts manual Series 3 and up
>>>> 
>>>> Help please
>>>> 
>>>> Jim
>>>> 
>>>> Jim Armstrong
>>>> Mk 1A
>>>> 382002083 
> 
>> 
>> <4aef7790.jpg>
> _______________________________________________
> 
> tigers at autox.team.net
> 
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/tigers http://autox.team.net/archive
> 
> Unsubscribe: http://autox.team.net/mailman/options/tigers/garywinblad@comcast.net
> 
> 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/tigers/attachments/20200527/51accf4a/attachment-0001.htm>