[Tigers] Thermostat Housing and Right Angle oil filter adapter

[Ron Fraser]

Joel

Thermostat housing

    The C5 part number is just the updated part number for that part.
I always note the Ford part number from the Rootes Parts List so you have
the base number to work from.
I don't have interchange or updated part number information available or I
would include that too.

Vacuum port

The 4100 4bbl uses the same parts as the 2100 2bbl.   It you have the 2bbl
parts available they should work with the 4bbl.

Ron Fraser

-----Original Message-----
From: Joel Martin [mailto:jmartiniii at yahoo.com]
Sent: Thursday, April 18, 2013 10:35 AM
To: Tiger List Serve; TheoSmit; Ron Fraser
Subject: RE: [Tigers] Thermostat Housing and Right Angle oil filter adapter



Summit carries the nipple AAF-ALL92003 or Ford Number F1AZ6890B, thanks
Theo, for $6.59 which is ~1" on block side and 3/4" - 16 on oil adapter
side.  I bought the Ford adapter M-68801-A50 as suggested on Tiger United
site for $79.95.  Hope this nipple works.  I really wanted to use the remote
oil filter set up but hose's were a challenge and cost prohibitive.

Scott Drake parts from Summit carries the spark plug wire separators, thanks
Ron, B8Q-12297-A for $1.93 and B6A-12297-A for $3.93.

Scott Drake parts from Summit references a different part number for the
thermostat housing C50E-8592-A for $17.97 instead of the C30Z-8594-B, thanks
Ron, but appears close as the angle is not a 90 degree like Ford part number
M-8592-M-90 for $33.95 which is a 90 degree.

You guys are keeping me moving.  Clutch bled, waiting on booster to come
back from rebuild, Petronix distributor and coil to be installed, fuel and
brake lines run, - no fuel from refurbished tanks thru fuel pump though -
always a challenge.  With the SS headers, will need to change choke to
electric or go to manual as no heat tube connections with headers unless
someone has a different idea for a heat tube alternative?

Not sure where on the Autolite 4100 carburetor to connect the ported vacuum
from the distributor to the carb though - any Ideas?

Thanks
Joel Martin



--- On Wed, 4/17/13, Smit, Theo <Theo.Smit at dynastream.com> wrote:



From: Smit, Theo <Theo.Smit at dynastream.com>
Subject: RE: [Tigers] Thermostat Housing and Right Angle oil filter adapter
To: "Joel Martin" <jmartiniii at yahoo.com>, "Tiger List Serve"
<Tigers at autox.team.net>
Date: Wednesday, April 17, 2013, 3:43 PM


Google is your friend...
F1AZ6890B

Apparently this part is about $8.66 at your local Ford parts counter.

Theo

> -----Original Message-----
> From: tigers-bounces at autox.team.net
<http://us.mc1647.mail.yahoo.com/mc/compose?to=tigers-bounces@autox.team.net
>  [mailto:tigers-
> bounces at autox.team.net
<http://us.mc1647.mail.yahoo.com/mc/compose?to=bounces@autox.team.net> ] On
Behalf Of Joel Martin
> Sent: April 17, 2013 1:07 PM
> To: Tiger List Serve
> Subject: [Tigers] Thermostat Housing and Right Angle oil filter adapter
>
> All
>
> Does anyone know a part number of correct thermostat housing?  Does it
> have just one nipple for a 66 MK 1A 289 motor?  I will be installing
> the heater core.
>
> Also, I purchased the FMS-M-6880-A50       90 DEGREE OIL FILTER
> ADAPTOR.  This
> requires a nipple adapter that goes into the block and then into the
> bolt of the adapter.  In checking with Summit, they said it was 3/4"
> x16 on both sides.  Apparently not, anyone know the correct nipple to
> purchase with part number  aaa x size on the block side and 3/4 x 16 on
> the adapter side.
>
> Thanks
> Joel Martin
> _______________________________________________
>
> tigers at autox.team.net
<http://us.mc1647.mail.yahoo.com/mc/compose?to=tigers@autox.team.net>
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
> http://autox.team.net/mailman/options/tigers/theo.smit@dynastream.com
>
>


________________________________

CONFIDENTIALITY NOTICE: This email and any attachments are for the sole use
of the intended recipient(s) and contain information that may be
confidential and/or legally privileged. If you have received this email in
error, please notify the sender by reply email and delete the message. Any
disclosure, copying, distribution or use of this communication (including
attachments) by someone other than the intended recipient is prohibited.
Thank you.