[Healeys] Chassis outriggers.

[Perry Small]

David
Just measured a untrusted piece of original outrigger and a replacement outrigger, I think from Kilmartin, at 0.080 inches or 14 gauge. 
Perry

Sent from my iPhone

> On Jul 25, 2022, at 11:22 PM, Jean Caron <vintage_roadster_restoration at hotmail.com> wrote:
> 
> 
> Way to go David.  Given the amount of rust on most Healeys, yes I am cheering in the background.
> 
> Jean
> 
> Sent from my Bell Samsung device over Canada’s largest network.
> From: David Lodge <emmgeeteecee at yahoo.co.uk>
> Sent: Monday, July 25, 2022 9:59:34 PM
> To: Jean Caron <vintage_roadster_restoration at hotmail.com>; Austin Healey <healeys at autox.team.net>; Perry Small <healeyguy at aol.com>; Bob Spidell <bspidell at comcast.net>; A. H. List <austinhealeyslist at gmail.com>
> Subject: Re: [Healeys] Chassis outriggers.
>  
> Hello Jean, Perry,
> 
> This is all original.  I've owned the car since '75 and is all original, apart from some accident damage, which was all superficial, i.e. no damage to the chassis or structural elements.  I'm cutting out all the rust.  Almost done, too!  (Is that cheering that I hear?)
> 
> 
> On Wed Jul 20 2022 05:35:26 GMT-0700 (PDT), Jean Caron <vintage_roadster_restoration at hotmail.com> wrote:
> 
> 
> David,
> Definitely never seen one of these before  do you know who perhaps made these at some point.
> 
> Jean
> 
> Sent from my Bell Samsung device over Canada’s largest network.
> From: Healeys <healeys-bounces at autox.team.net> on behalf of David Lodge via Healeys <healeys at autox.team.net>
> Sent: Friday, July 15, 2022 7:08:46 PM
> To: Austin Healey <healeys at autox.team.net>; A. H. List <austinhealeyslist at gmail.com>; David Nock BCS <healeydoc at sbcglobal.net>; dwflagg at juno.com <dwflagg at juno.com>; rjhco at att.net <rjhco at att.net>; sbyers at ec.rr.com <sbyers at ec.rr.com>
> Subject: Re: [Healeys] Chassis outriggers.
>  
> 
> Attached, photos of the left rear chassis outrigger.  Unlike any species of same before or since!
> On Tuesday, 12 July 2022 at 13:02:59 GMT-7, David Lodge via Healeys <healeys at autox.team.net> wrote:
> 
> 
> Greetings all!
> 
> Does anyone please happen to know the correct gauge of steel used on the BJ8 chassis outriggers?  Mine are so badly corroded on the inside that it's impossible to tell!  If I'm VERY careful I'll be able to get a pattern off them, at least!
> 
> Thanks to all.
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation  $12.75
> 
> Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive/healeys
> 
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
> 
> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/emmgeeteecee@yahoo.co.uk
> 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/healeys/attachments/20220726/bb6d1261/attachment.htm>