[Healeys] Throttle shaft rebush

[David Nock]

If your transmission is out then replace the throttle bushing before you re install the transmission.


David Nock
healeydoc at sbcglobal.net
209 948 8767
www.britishcarspecialists.com

From: Tim Davis BN7 
Sent: Sunday, October 11, 2015 6:37 AM
To: goldengt 
Cc: Healey List 
Subject: Re: [Healeys] Throttle shaft rebush

OK thanks I was heading in the right direction, I'll put the tranny back in then jack up and finish the bushes.

Thanks




--------------------------------------------------------------------------------

From: "goldengt" <goldengt at cal.net>
To: "Tim Davis BN7" <tld6008 at mchsi.com>, "richard mayor" <boyracer466 at gmail.com>
Cc: "Healey List" <healeys at autox.team.net>
Sent: Saturday, October 10, 2015 8:19:30 PM
Subject: Re: [Healeys] Throttle shaft rebush


Use 1/4 sockets and enough extensions so you can lay on the floor. Engine trans in place. 



Sent from my Verizon Wireless 4G LTE smartphone
-------- Original message --------
From: Tim Davis BN7 <tld6008 at mchsi.com> 
Date: 10/10/2015 3:56 PM (GMT-08:00) 
To: richard mayor <boyracer466 at gmail.com> 
Cc: Healey List <healeys at autox.team.net> 
Subject: Re: [Healeys] Throttle shaft rebush 

That is close but I need something in addition to that. Do you recall if the clutch was in place?




--------------------------------------------------------------------------------

From: "richard mayor" <boyracer466 at gmail.com>
To: "Tim Davis BN7" <tld6008 at mchsi.com>
Cc: "Healey List" <healeys at autox.team.net>
Sent: Saturday, October 10, 2015 3:27:29 PM
Subject: Re: [Healeys] Throttle shaft rebush


I seem to recall using a 1/4" drive socket to get to the back bolts. 


On Sat, Oct 10, 2015 at 9:36 AM, Tim Davis BN7 <tld6008 at mchsi.com> wrote:

  There was a tech article in the May 2006 issue of Austin Healey magazine where Norman Nock described the wear points in the 3000 throttle linkages and briefly discusses removing and replacing them. Specific to my situation is where he describes  the replacing of the bushes on the 15" cross-shaft above the bellhousing. Also for added convinience he suggests removing the transmission cover. And then work the right bracket from under the bonnet  and from below the car on the left side.

  I am attempting to do this since I have my transmission out but for the life of me can't remove the rear bolt on each bracket. I have yet to remove the clutch which would gain me more access and I can't get under my car. I know this can be done but I need a few hints..Please!!

  Tim Davis BN7



  _______________________________________________
  Support Team.Net http://www.team.net/donate.html
  Suggested annual donation  $12.75
  Archive: http://www.team.net/archive
  Forums: http://www.team.net/forums

  Healeys at autox.team.net
  http://autox.team.net/mailman/listinfo/healeys

  Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/boyracer466@gmail.com








--------------------------------------------------------------------------------
_______________________________________________
Support Team.Net http://www.team.net/donate.html
Suggested annual donation  $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

Healeys at autox.team.net
http://autox.team.net/mailman/listinfo/healeys

Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/healeydoc@gmail.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/healeys/attachments/20151012/a180de38/attachment.html>