[Healeys] Rear axle gasket question

Mon Jan 26 14:46:27 MST 2015

Well you may be over thinking it but you are at least keeping us amused :-)
BTW the BN1, BN2 and 100S didn't have the "O" ring seal so I think in their
cases the gasket was the seal..
Pooffff goes that theory..
Michael S
BN1 #174

On Mon, Jan 26, 2015 at 4:36 PM, Steve B. Gerow <steveg at abrazosdata.com>
wrote:

> The whole idea of the gasket-as-shim has a certain logic to it - except
> the o-ring does the actual sealing, correct?
>
> Is this the idea: when we tighten the lug nuts, we compress the gasket
> from, say .014" to .010". At .010, the axle center makes contact with the
> spacer ring and bearing, coming to a stop. There is then .010" between the
> carrier and axle flange. The gasket takes up the slack - is the compressed
> gasket strong enough to in effect be a shim between these two parts?
>
> Michael - maybe when extra-tightening of the lug nuts, the axle flange is
> also bending slightly to take up this gap.
>
> Betcha I'm over-thinking this! :-)
>
>
>
> --
> Steve Gerow
>
>
>
> >  -------Original Message-------
> >  From: Michael Salter <michaelsalter at gmail.com>
> >  To: Steve B. Gerow <steveg at abrazosdata.com>
> >  Cc: warthodson at aol.com <warthodson at aol.com>,
> simon.lachlan at homecall.co.uk, healeys at autox.team.net
> >  Subject: Re: [Healeys] Rear axle gasket question
> >  Sent: Jan 26 '15 11:28
> >
> >  One other observation on this subject.
> >
> >
> >  This is, I believe, the only place on a Healey where 'conical" seat nuts
> >  are used.
> >  It has been my experience that conical seat nuts always require
> re-torquing
> >  after a little  use. Just like the lug nuts on your every day driver if
> >  you torque them up, then drive the car for a bit you will find that the
> >  nuts will take up to half a turn just to restore them to the original
> >  torque.
> >
> >
> >  That said however I do have to agree with Chris regarding aggressive
> use.
> >  On AHX12 we found it necessary to re-torque those nuts after every day
> of
> >  competition and they would always go on an additional flat or so.. I
> always
> >  wondered where that extra tightening room came from because after a
> week of
> >  Targa Newfoundland we would have tightened the nuts at least one full
> turn
> >  ... that's 0.055".
> >
> >
> >  I "forgot" to mention to co-driver Michael O that a likely cause was
> >  stretching of the studs..:-).
> >
> >
> >  Michael S
> >  [LINK: http://www.acmefluid.com.au/larry/ahx12.html]
> >  http://www.acmefluid.com.au/larry/ahx12.html
> >
> >
> >  On Mon, Jan 26, 2015 at 12:25 PM, Steve B. Gerow <[LINK:
> >  mailto:steveg at abrazosdata.com] steveg at abrazosdata.com> wrote:
> >  Some observations:
> >  New Moss gasket - .014"
> >  Old gasket originally coated with Hylomar, as removed from axle - .010"
> >
> >  .004" = copier paper
> >
> >  My axle is buttoned up with a new gasket and the rear rotor/caliper back
> >  in place or I'd try to do a science project here.
> >
> >  For a gasket thickness, perhaps if one were to bolt the assembly
> together
> >  without gasket and measure the gap with shims, then add .003" to that.
> >
> >  The new bearing, assembled with heat and cold per Tom Monaco's
> >  instructions, is a tight fit in the carrier and axle - IIRC the bearing
> >  depends on this more than the compression of the spacer, gasket, etc.
> >
> >
> >  --
> >  Steve Gerow
> >  Altadena, CA
> >  BN6
> >
> >
> >  >  -------Original Message-------
> >  >  From: [LINK: mailto:warthodson at aol.com] warthodson at aol.com
> >  >  To: [LINK: mailto:simon.lachlan at homecall.co.uk]
> >  simon.lachlan at homecall.co.uk, [LINK: mailto:steveg at abrazosdata.com]
> >  steveg at abrazosdata.com, [LINK: mailto:healeys at autox.team.net]
> >  healeys at autox.team.net
> >  >  Subject: Re: [Healeys] Rear axle gasket question
> >  >  Sent: Jan 26 '15 08:41
> >  >
> >  >  I have not tried it but I doubt it. On the three axles I have actual
> >  >  experience with the gasket needed to be Approx. 0.004" thick so that
> >  the
> >  >  spacer met the specified tolerances in the workshop manual. The
> >  gaskets I
> >  >  purchased were all approx. 0.010" thick. That would be a lot of
> >  squish. You
> >  >  would have to squish it without the bearing spacer in place. Then
> >  remove
> >  >  the axle & measure how much the spacer stood proud of the gasket.
> Then
> >  >  reassemble everything, if it met spec. It seemed easier to just make
> a
> >  >  gasket of the proper thickness.
> >  >
> >  >  Gary Hodson
> >  >
> >  >
> >  >  From: Simon Lachlan <[LINK: mailto:simon.lachlan at homecall.co.uk]
> >  simon.lachlan at homecall.co.uk>
> >  >  Subject: RE: [Healeys] Rear axle gasket question
> >  >
> >  >
> >  >  If you soaked the too big gaskets in, say, WD40, wouldn’t they
> >  compress
> >  >  down to a proper size as you tightened up?
> >  >
> >  >  Just a thought..............
> >  >
> >  >  Simon
> >  _______________________________________________
> >  Support Team.Net [LINK: http://www.team.net/donate.html]
> >  http://www.team.net/donate.html
> >  Suggested annual donation  $12.75
> >  Archive: [LINK: http://www.team.net/archive]
> http://www.team.net/archive
> >  Forums: [LINK: http://www.team.net/forums] http://www.team.net/forums
> >
> >  [LINK: mailto:Healeys at autox.team.net] Healeys at autox.team.net
> >  [LINK: http://autox.team.net/mailman/listinfo/healeys]
> >  http://autox.team.net/mailman/listinfo/healeys
> >
> >  Unsubscribe/Manage: [LINK:
> >  http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com]
> >  http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com
> >
> >
> >  --
> >
> >
> >  If you can't fix it with a hammer, you've got an electrical problem.
>

-- 
*If you can't fix it with a hammer, you've got an electrical problem.*
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/healeys/attachments/20150126/e6abca9d/attachment.html>