[Fot] Do(o)med or flat lifters?

[Joe Boruch]

What motor oil are you using?  Lack of zinc may be a cause of the lifter pitting.  Joe(B)

---------- Original Message ----------
From: Christian Marx via Fot <fot at autox.team.net>
To: "fot at autox. team. net" <fot at autox.team.net>
Subject: [Fot] Do(o)med or flat lifters?
Date: Mon, 23 Jul 2018 12:08:28 +0300


In the past we had this discussion.I've bought some high quality lifters from USA, made from tool steel I suppose. 400$ they've cost..... and started to fail. On 3 of them, the very center does show e few pittings. Also visible that only a small part of the Cam is used.. The cam is okay  The machine shop will grind the lifters dead flat, as they should be, they say. CheersChris
Am 18.07.2018 02:12 schrieb "fubog1 via Fot" <fot at autox.team.net>:
Yes, lacking access to a Cam Doc, you can use a set of V or bearing blocks, a degree wheel, dial indicator, and a bit of time, checked at 5 cam degrees, works fine.I'm still old school though, I plot them out on graph paper!
 That will give you the lobe profile but most folks don't have the full specs on the cam, usually just advertised lift and duration.Since the tip of the lobe usually starts to go away first, a simple lift measurement will reveal the worst, best done with a dial indicator cuz some (cheap) cams are ground on different base circles.Generally, ramp wear is unusual if the tip is still OK, although there can be exceptions.
 Glen.
    -----Original Message-----
 From: timmmurphh <timmmurphh at gmail.com>
 To: 'fubog1' <fubog1 at aol.com>; rbtr3a <rbtr3a at cox.net>
 Sent: Tue, Jul 17, 2018 12:38 pm
 Subject: RE: [Fot] Cams
 
By degreeing the cam using increments of 10 crankshaft degrees (5 camshaft degrees) and then plotting the results in Excel, it is possible to get a very accurate picture of the profile of the cam. I’ve attached a spreadsheet showing an intake and exhaust lobe comparison two years apart of our Kastner G3 cam for reference. Tim Murphy#317 TR4 From: Fot <fot-bounces at autox.team.net> On Behalf Of fubog1 via Fot
 Sent: Monday, July 16, 2018 6:31 AM
 To: rbtr3a at cox.net; fot at autox.team.net
 Subject: Re: [Fot] Cams Generally any obvious wear or pitting would make it unserviceable, but the wear isn't always so obvious.You can measure the lift and compare to spec, that will show any worn lobes, but the best way is to find someone who has a "cam doctor". It's a machine that sets it up and measures the complete profile.Usually if there is anything apparent that suggests that there may be problems, there are... Glen  -----Original Message-----
 From: rbtr3a--- via Fot <fot at autox.team.net>
 To: fot <fot at autox.team.net>
 Sent: Sun, Jul 15, 2018 6:47 pm
 Subject: [Fot] Cams
 
 How do I determine if a cam is good or bad. If there are any marks on it does that make it bad. I do know that two of the lifters has pitting on the surface. 
 
 Ronnie
 _______________________________________________
 fot at autox.team.net
 
 http://www.fot-racing.com
 
 Donate: http://www.team.net/donate.html
 Archive: http://www.team.net/pipermail/fot
 Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/fubog1@aol.com
 
 _______________________________________________
 fot at autox.team.net
 
 http://www.fot-racing.com
 
 Donate: http://www.team.net/donate.html
 Archive: http://www.team.net/pipermail/fot
 Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/tr4racing@googlemail.com
 
 
____________________________________________________________
Unbelievable German World War 2 Photo Shocks Americans
pro.naturalhealthresponse.com
http://thirdpartyoffers.netzero.net/TGL3231/5b55d557f30e355573d69st04duc
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/fot/attachments/20180723/65fe83c2/attachment-0001.htm>