[6pack] Throttle Linkage ?S? Connectors

[rmf3860 rmf3860]

Thanks Tom. I have a heat deflector. I bought it many years ago.
Considering the slop in my throttle linkage, I decided to order a
replacement from Richard at Goodparts.

Bob Fabie

On Wed, Nov 24, 2021 at 6:36 AM Tomislav Marincic <
tomislav.marincic at earthlink.net> wrote:

> Hello Robert,
>
> I'll snap you a photo of the barrel linkage in place. One of them works,
> but if I recall correctly, there was no way to use two and get them
> installed without removing the carbs and linkage.
>
> I Jet Hot coated both of my manifolds, and wrapped the exhaust header in
> Thermo-Tec exhaust tape. The Jet Hot keeps the manifolds looking nice, and
> keeps the header from corroding, but it won't cure your fuel cook-off
> problems. Your best bet is one of Joe Alexander's heat shields, which I
> think are being sold through Moss as well.
> https://mossmotors.com/aluminum-heat-shield-by-a-r-e-for-zenith-stromberg-carbs?utm_source=feed&utm_medium=free&utm_campaign=shopping&gclid=EAIaIQobChMI4v7154Cx9AIVhcqGCh0tWAy8EAQYAiABEgKXSPD_BwE
> (
> https://mossmotors.com/aluminum-heat-shield-by-a-r-e-for-zenith-stromberg-carbs?utm_source=feed&utm_medium=free&utm_campaign=shopping&gclid=EAIaIQobChMI4v7154Cx9AIVhcqGCh0tWAy8EAQYAiABEgKXSPD_BwE
> )
>
> https://www.summitracing.com/parts/the-11021?rrec=true (
> https://www.summitracing.com/parts/the-11021?rrec=true)
>
> Good Luck, Tom
>
>
>
>
> -----Original Message-----
> From: robert rudolphi
> Sent: Nov 23, 2021 1:23 PM
> To: 6pack at autox.team.net , Tomislav Marincic
> Subject: Re: [6pack] Throttle Linkage ?S? Connectors
>
> To follow up on this I am having my carbs rebuilt this winter (Joe Curto)
> and was thinking about have the intake and stock exhaust manifolds Jet
> coated. I am trying to reduce hard starting when hot. Would also like to
> get the throttle linkages re-plated/refinished and was wondering what is
> the best way to go?
>
> Thanks in advance for any feedback
>
> Robert
>
>
>
>
>
> On Tuesday, November 23, 2021, 12:13:49 PM EST, Tomislav Marincic wrote:
>
>
>
>
>
>
> When I set up my dual ZS175’s I used new link clips from Roadster Factory.
> They quickly became distorted and introduced slop into the linkage.
>
> I’m currently using one SU link clip sourced from Richard Good, which is
> much sturdier and more rust-resistant than the ZS part. I’m also using a
> single rigid coupling that I sourced from Grainger. I forget why, but
> installing two shaft linkages was problematic, and the gap between carb
> throttle shafts was too wide to use two SU linkages.
>
> I might have one of each in my spares if you need them.
>
> https://www.grainger.com/search?searchQuery=nomar+clx-5-5-a&searchBar=true
>
> https://www.goodparts.com/product/folded-coupler-carb-shaft/
>
> Pix on request…Tom
>
>
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation  $12.96
> Archive: http://www.team.net/archive
>
>
> 6pack at autox.team.net
> http://autox.team.net/mailman/listinfo/6pack
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/6pack/robertrudolphi@yahoo.com
>
>
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation  $12.96
> Archive: http://www.team.net/archive
>
>
> 6pack at autox.team.net
> http://autox.team.net/mailman/listinfo/6pack
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/6pack/bobfabie@gmail.com
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/6pack/attachments/20211124/ed838233/attachment.htm>