triumphs
[Top] [All Lists]

Re: TR6 Misfire (here we go again!)

To: thoward@sdcoe.k12.ca.us, duhart@symbol.com
Subject: Re: TR6 Misfire (here we go again!)
From: John Duhart <duhart@symbol.com>
Date: Thu, 21 May 1998 13:48:39 -0400
Cc: triumphs@Autox.Team.Net
Hey All,

 I have some info I want to tell everyone.  I have the Vacuum advance attached 
to the Dist.  Setup this way I have set the timing to 10 degrees BTDC, with the 
car idling at 800RPM.  A lot of people asked about the Vacuum advance, so is 
this a problem?  What does it mean to do 'static' timing?

Later,
JHD IV

>>> Thomas Howard <thoward@sdcoe.k12.ca.us> 05/21 9:32 AM >>>
You need to determine if the trouble is spark, fuel, or cam timing.

Since the engine is new it could be anything.

Check the exhust.  Clear?  Sooty?

Check the plug color, Black?  Brown?  Gray?

Move the ignition timeing while the engine is running and observe the changes.

Can you draw a long spark from a plug wire to the block?  (more then 1/2
inch)  (it take a lot more juice to spark under compression than in free air)

Cam timing you will have to check with the valve cover off and a degree
wheel.  Is there any reason to suspect this?

How about that 10 degrees of spart time.   Is that static, running, with or
without vaccume?   

At 07:47 AM 5/21/98 -0400, you wrote:
>
>Hey All,
>
> OK, I took the TR6 out last night to get ready for an inspection.  Let me
remind everyone that I have just finished a rebuild on the engine, and all
other mechanical parts on the car.  The car has about 10-15 miles on it
since the rebuild.
>
> I put new Champion spark plugs (Y12NC?) in, gapped at .025 in.  Car has a
slight misfire at idle, but that is not what is worrying me.  When I try to
accellarate the engine mis-fires badly.  I had driven it once since the
rebuild with BOSCH plugs in it gapped at about .045in, and I don't recall
this problem.  Once I have the car going at about 20-30 MPH, if I let up on
the gas the mis-fire isn't as bad.  Hoiwever I can't see the car being able
to do more than 40MPH the way it is right now!
>
> I checked the points and they are gapped at .015in.  Timing is set at 10
degrees BTDC
>
> I'm going to puy the Bosch plugs back in and see what if this is a new
problem or just something I didn't notice the first time I drove it.
>
> If anyone has any suggestions on what to look for please foward them.
And yes I haven't adjusted the carbs on it since the rebuild, no balance
and there needle adjust is set at half a turn from full lean, so if it is
not the plugs this is were I will start.
>
>Later,
>JHD IV
>












    !
>                                
>                                       
>
>

Tom Howard
'72 GT6 (and a good bit of USA iron)
Lakeside Union School District

                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                               
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                          !
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                               
                                                                                
                  

<Prev in Thread] Current Thread [Next in Thread>