shop-talk
[Top] [All Lists]

Re: [Shop-talk] Air impact dead?

To: "shop-talk@autox.team.net" <Shop-talk@autox.team.net>
Subject: Re: [Shop-talk] Air impact dead?
From: Scott Hall <scott.hall.personal@gmail.com>
Date: Thu, 4 Feb 2021 09:10:10 -0600
Delivered-to: mharc@autox.team.net
Delivered-to: Shop-talk@autox.team.net
References: <CAK73_u6nZJr=CEPEWs_93hrHKd+nhMe+W3AfC=M4pfXaHbEkmQ@mail.gmail.com> <CAG1pxgYqQETQgs_3GxX6kEqz5N+GaCQE1wAjD6gTjaygUF8RWg@mail.gmail.com>
--===============0543795444225347964==

--000000000000a4339905ba841bd2

Following up:

There was nothing wrong with the wrench.

The female quick-disconnect at the compressor wasn't seating correctly
which wasn't allowing full air flow to the tool.

When I pushed in the hose to connect it, the hose connected and wasn't
hissing. If you grab the male fitting and force it another half-inch or so
into the female fitting, you get normal function.

I don't know if the fitting itself is defective or if I bought the wrong
fitting. They're all Harbor Freight 'industrial'-type fittings....which
might answer my question for me.

On a side note, I've never tried to use an air tool with a small tank...and
I won't be trying any more. This may be the excuse to buy the Quincy I've
always wanted.

Scott

On Fri, Jan 22, 2021 at 12:43 PM old dirtbeard <dirtbeard@gmail.com> wrote:

> I have seen this with seldom used air impact wrenches. The air paddles in
> the motor get stuck in their slots and will not seal. You will hear the air
> escaping from the wrench, but with little movement or power.
>
> You could try to squirt some air tool oil in it, spin it just a little to
> spread it around the paddles, let it set for a few hours and try it again
> to see if it free the paddles before you open it up.
>
> best,
>
> doug
>
> On Fri, Jan 22, 2021 at 10:08 AM Scott Hall <scott.hall.personal@gmail.com>
> wrote:
>
>> IR2131 - 1/2" impact.
>>
>> It's maybe 20 years old. Been used maybe half a dozen times in twenty
>> years (it has a brother that gets used usually) and has lived a coddled
>> life in a padded tool drawer. Not even really dusty.
>>
>> Tried it the other day and it acts like there's no air in the compressor.
>> Turns really slow with no power at all. Not even a first good smack.
>>
>> I'm trying to use it with a portable roofing compressor (the two long
>> tanks, maybe three gallon capacity), but it puts out 100+ p.s.i. and it
>> filled up.
>>
>> Should I try to take it (the wrench) apart and see if something's in the
>> passages? Do they just wear out over time, even if not used? Might the
>> compressor be too small? My only thought is maybe a wasp got into it and
>> made a nest somewhere in there. I don't *see* anything, but...
>> _______________________________________________
>>
>> Shop-talk@autox.team.net
>> Donate: http://www.team.net/donate.html
>> Suggested annual donation  $12.96
>> Archive: http://www.team.net/pipermail/shop-talk
>> http://autox.team.net/archive
>>
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/shop-talk/dirtbeard@gmail.com
>>
>>

--000000000000a4339905ba841bd2
Content-Transfer-Encoding: quoted-printable

<div dir=3D"ltr">Following up:<div><br></div><div>There was nothing wrong w=
ith the wrench.</div><div><br></div><div>The female quick-disconnect at the=
 compressor wasn&#39;t seating correctly which wasn&#39;t allowing full air=
 flow to the tool.</div><div><br></div><div>When I pushed in the hose to co=
nnect it, the hose connected and wasn&#39;t hissing. If you grab the male f=
itting and force it another half-inch or so into the female fitting, you ge=
t normal function.</div><div><br></div><div>I don&#39;t know if the fitting=
 itself is defective or if I bought the wrong fitting. They&#39;re all Harb=
or Freight &#39;industrial&#39;-type fittings....which might answer=C2=A0my=
 question for me.</div><div><br></div><div>On a side note, I&#39;ve never t=
ried to use an air tool with a small tank...and I won&#39;t be trying any m=
ore. This may be the excuse to buy the Quincy I&#39;ve always=C2=A0wanted.<=
/div><div><br></div><div>Scott</div></div><br><div class=3D"gmail_quote"><d=
iv dir=3D"ltr" class=3D"gmail_attr">On Fri, Jan 22, 2021 at 12:43 PM old di=
rtbeard &lt;<a href=3D"mailto:dirtbeard@gmail.com";>dirtbeard@gmail.com</a>&=
gt; wrote:<br></div><blockquote class=3D"gmail_quote" style=3D"margin:0px 0=
px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div =
dir=3D"ltr">I have seen this with seldom used air impact wrenches. The air =
paddles in the motor get stuck in their slots and will not seal. You will h=
ear the air escaping from the wrench, but with little movement or power.<di=
v><br></div><div>You could try to squirt some air tool oil in it, spin it j=
ust a little to spread it around the paddles, let it set for a few hours an=
d try it again to see if it free the paddles before you open it up.</div><d=
iv><br></div><div>best,</div><div><br></div><div>doug</div></div><br><div c=
lass=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Fri, Jan 22, =
2021 at 10:08 AM Scott Hall &lt;<a href=3D"mailto:scott.hall.personal@gmail=
.com" target=3D"_blank">scott.hall.personal@gmail.com</a>&gt; wrote:<br></d=
iv><blockquote class=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;bord=
er-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir=3D"ltr">IR213=
1 - 1/2&quot; impact.<div><br></div><div>It&#39;s maybe 20 years old. Been =
used maybe half a dozen times in twenty years (it has a brother that gets u=
sed usually) and has lived a coddled life in a padded tool drawer. Not even=
 really dusty.</div><div><br></div><div>Tried it the other day and it acts =
like there&#39;s no air in the compressor. Turns really slow with no power =
at all. Not even a first good smack.</div><div><br></div><div>I&#39;m tryin=
g to use it with a portable roofing compressor (the two long tanks, maybe t=
hree gallon capacity), but it puts out 100+ p.s.i. and it filled up.</div><=
div><br></div><div>Should I try to take it (the wrench) apart and see if so=
mething&#39;s in the passages? Do they just wear out over time, even if not=
 used? Might the compressor be too small? My only thought is maybe a wasp g=
ot into it and made a nest somewhere in there. I don&#39;t *see* anything, =
but...</div></div>
_______________________________________________<br>
<br>
<a href=3D"mailto:Shop-talk@autox.team.net"; target=3D"_blank">Shop-talk@aut=
ox.team.net</a><br>
et=3D"_blank">http://www.team.net/donate.html</a><br>
Archive: <a href=3D"http://www.team.net/pipermail/shop-talk"; rel=3D"norefer=
rer" target=3D"_blank">http://www.team.net/pipermail/shop-talk</a> <a href=
=3D"http://autox.team.net/archive"; rel=3D"noreferrer" target=3D"_blank">htt=
p://autox.team.net/archive</a><br>
<br>
alk/dirtbeard@gmail.com" rel=3D"noreferrer" target=3D"_blank">http://autox.=
team.net/mailman/options/shop-talk/dirtbeard@gmail.com</a><br>
<br>
</blockquote></div>
</blockquote></div>

--000000000000a4339905ba841bd2--

--===============0543795444225347964==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________

Shop-talk@autox.team.net
Archive: http://www.team.net/pipermail/shop-talk http://autox.team.net/archive



--===============0543795444225347964==--

<Prev in Thread] Current Thread [Next in Thread>