Re: [Healeys] Speedo Cable

[Hank Leach via Healeys <healeys@autox.team.net>]

--===============4217651557144071171==
Content-Transfer-Encoding: quoted-printable

<div>I say its best to remove the console/tunnel cover for access. There is=
 a clip on the OD bolt that steadies the cable as well if factory installed=
. Patience is a virtue. Hank<br>-------------------- <br><br>From: &lt;m.g.=
sharp@sympatico.ca&gt; <br>To: "'Roger Grace'" &lt;roggrace@telus.net&gt;, =
"'Healeys'" &lt;healeys@autox.team.net&gt; <br>Sent: October 21, 2024 at =
8:28 PM PDT <br>Subject: Re: [Healeys] Speedo Cable </div>
<div class=3D"WordSection1">
<p class=3D"MsoNormal"><span =
style=3D"font-size: 11.0pt; font-family: 'Calibri',sans-serif; =
mso-fareast-language: EN-US;">Roger,&nbsp; No experience with the BJ8, but =
likely the same as my BT7, and I have removed the complete cable before =
without removing the gearbox cover.&nbsp; It is a real fiddle as it is =
obscured by the cruciform in the frame.&nbsp; I seem to recall I used some =
long needle-nose pliers and could just get enough grip on the knurled =
&ldquo;nut&rdquo; that holds the cable onto the angle drive to undo it.=
&nbsp; I don&rsquo;t think I removed the angle drive, but in truth =
can&rsquo;t recall.&nbsp; It was painstaking as I could only rotate the =
knurled piece a tiny bit at a time.&nbsp; In the end, it may have been less=
 frustration to remove the cover.&nbsp; However, it worth a try.&nbsp; Good=
 luck with it!</span></p>
<p class=3D"MsoNormal"><span style=3D"font-size: =
11.0pt; font-family: 'Calibri',sans-serif; mso-fareast-language: =
EN-US;">&nbsp;</span></p>
<p class=3D"MsoNormal"><span style=3D"font-size: =
11.0pt; font-family: 'Calibri',sans-serif; mso-fareast-language: =
EN-US;">Mirek</span></p>
<p class=3D"MsoNormal"><span style=3D"font-size: =
11.0pt; font-family: 'Calibri',sans-serif; mso-fareast-language: =
EN-US;">&nbsp;</span></p>
<div style=3D"border: none; border-top: solid =
#E1E1E1 1.0pt; padding: 3.0pt 0cm 0cm 0cm;">
<p class=3D"MsoNormal"><strong=
><span style=3D"font-size: 11.0pt; font-family: 'Calibri',=
sans-serif;">From:</span></strong><span style=3D"font-size: 11.0pt; =
font-family: 'Calibri',sans-serif;"> Healeys &lt;healeys-bounces@autox.team=
.net&gt; <strong>On Behalf Of </strong>Roger Grace<br><strong>Sent:</strong=
> October 21, 2024 10:10 PM<br><strong>To:</strong> Healeys =
&lt;healeys@autox.team.net&gt;<br><strong>Subject:</strong> [Healeys] =
Speedo Cable</span></p>
</div>
<p class=3D"MsoNormal">&nbsp;</p>
<div>
<div>
<p class=3D"MsoNormal">BJ8</p>
</div>
<div>
<p class=3D"MsoNormal">I =
need to remove the speedo cable from my BJ8 - not just the inner&nbsp; but =
the complete cable at the rt angle drive.</p>
</div>
<div>
<p class=3D"MsoNormal">So, wondering if the more experienced could comment =
if this can be done from downstairs without removing the GB cover ?</p>
</div>
<div>
<p class=3D"MsoNormal">Any thoughts, ideas or tricks =
appreciated.</p>
</div>
<div>
<p class=3D"MsoNormal">rg</p>
</div>
<div>
<p class=3D"MsoNormal">&nbsp;</p>
</div>
<div>
<p class=3D"MsoNormal">&nbsp=
;</p>
</div>
</div>
</div>
<div>&nbsp;</div>

--===============4217651557144071171==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________

Archive: http://www.team.net/pipermail/healeys 
http://autox.team.net/archive/healeys

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys



--===============4217651557144071171==--