--===============3596593317536685076==
--000000000000301abb0625092452
Content-Transfer-Encoding: quoted-printable
Removing the GB cover is generally pretty easy, I would just take it off.
Probably only 15 min worth of work, just about the same amount of time
you'll spend putting it on a lift.
Cheers,
Alan
On Tue, Oct 22, 2024 at 11:30=E2=80=AFAM <m.g.sharp@sympatico.ca> wrote:
> Roger, No experience with the BJ8, but likely the same as my BT7, and I
> have removed the complete cable before without removing the gearbox cover=
.
> It is a real fiddle as it is obscured by the cruciform in the frame. I
> seem to recall I used some long needle-nose pliers and could just get
> enough grip on the knurled =E2=80=9Cnut=E2=80=9D that holds the cable ont=
o the angle drive
> to undo it. I don=E2=80=99t think I removed the angle drive, but in trut=
h can=E2=80=99t
> recall. It was painstaking as I could only rotate the knurled piece a ti=
ny
> bit at a time. In the end, it may have been less frustration to remove t=
he
> cover. However, it worth a try. Good luck with it!
>
>
>
> Mirek
>
>
>
> *From:* Healeys <healeys-bounces@autox.team.net> *On Behalf Of *Roger
> Grace
> *Sent:* October 21, 2024 10:10 PM
> *To:* Healeys <healeys@autox.team.net>
> *Subject:* [Healeys] Speedo Cable
>
>
>
> BJ8
>
> I need to remove the speedo cable from my BJ8 - not just the inner but
> the complete cable at the rt angle drive.
>
> So, wondering if the more experienced could comment if this can be done
> from downstairs without removing the GB cover ?
>
> Any thoughts, ideas or tricks appreciated.
>
> rg
>
>
>
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
>
> Archive: http://www.team.net/pipermail/healeys
> http://autox.team.net/archive/healeys
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/healey.nut@gmail.com
>
>
--000000000000301abb0625092452
Content-Transfer-Encoding: quoted-printable
<div dir=3D"ltr">Removing the GB cover is generally pretty easy, I would ju=
st take it off.=C2=A0 Probably only 15 min worth of work, just about the sa=
me amount of time you'll spend putting it on a lift.<br><br>Cheers,<br>=
<br>Alan</div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmai=
l_attr">On Tue, Oct 22, 2024 at 11:30=E2=80=AFAM <<a href=3D"mailto:m.g.=
sharp@sympatico.ca">m.g.sharp@sympatico.ca</a>> wrote:<br></div><blockqu=
ote class=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;border-left:1px=
solid rgb(204,204,204);padding-left:1ex"><div class=3D"msg8721052426919501=
011"><div lang=3D"EN-CA" style=3D"overflow-wrap: break-word;"><div class=3D=
"m_8721052426919501011WordSection1"><p class=3D"MsoNormal"><span style=3D"f=
ont-size:11pt;font-family:Calibri,sans-serif">Roger,=C2=A0 No experience wi=
th the BJ8, but likely the same as my BT7, and I have removed the complete =
cable before without removing the gearbox cover.=C2=A0 It is a real fiddle =
as it is obscured by the cruciform in the frame.=C2=A0 I seem to recall I u=
sed some long needle-nose pliers and could just get enough grip on the knur=
led =E2=80=9Cnut=E2=80=9D that holds the cable onto the angle drive to undo=
it.=C2=A0 I don=E2=80=99t think I removed the angle drive, but in truth ca=
n=E2=80=99t recall.=C2=A0 It was painstaking as I could only rotate the knu=
rled piece a tiny bit at a time.=C2=A0 In the end, it may have been less fr=
ustration to remove the cover.=C2=A0 However, it worth a try.=C2=A0 Good lu=
ck with it!<u></u><u></u></span></p><p class=3D"MsoNormal"><span style=3D"f=
ont-size:11pt;font-family:Calibri,sans-serif"><u></u>=C2=A0<u></u></span></=
p><p class=3D"MsoNormal"><span style=3D"font-size:11pt;font-family:Calibri,=
sans-serif">Mirek<u></u><u></u></span></p><p class=3D"MsoNormal"><span styl=
e=3D"font-size:11pt;font-family:Calibri,sans-serif"><u></u>=C2=A0<u></u></s=
pan></p><div style=3D"border-right:none;border-bottom:none;border-left:none=
;border-top:1pt solid rgb(225,225,225);padding:3pt 0cm 0cm"><p class=3D"Mso=
Normal"><b><span lang=3D"EN-US" style=3D"font-size:11pt;font-family:Calibri=
,sans-serif">From:</span></b><span lang=3D"EN-US" style=3D"font-size:11pt;f=
ont-family:Calibri,sans-serif"> Healeys <<a href=3D"mailto:healeys-bounc=
es@autox.team.net" target=3D"_blank">healeys-bounces@autox.team.net</a>>=
<b>On Behalf Of </b>Roger Grace<br><b>Sent:</b> October 21, 2024 10:10 PM<=
br><b>To:</b> Healeys <<a href=3D"mailto:healeys@autox.team.net"; target=
=3D"_blank">healeys@autox.team.net</a>><br><b>Subject:</b> [Healeys] Spe=
edo Cable<u></u><u></u></span></p></div><p class=3D"MsoNormal"><u></u>=C2=
=A0<u></u></p><div><div><p class=3D"MsoNormal">BJ8<u></u><u></u></p></div><=
div><p class=3D"MsoNormal">I need to remove the speedo cable from my BJ8 - =
not just the inner=C2=A0 but the complete cable at the rt angle drive.<u></=
u><u></u></p></div><div><p class=3D"MsoNormal">So, wondering if the more ex=
perienced could comment if this can be done from downstairs without removin=
g the GB cover ?<u></u><u></u></p></div><div><p class=3D"MsoNormal">Any tho=
ughts, ideas or tricks appreciated.<u></u><u></u></p></div><div><p class=3D=
"MsoNormal">rg<u></u><u></u></p></div><div><p class=3D"MsoNormal"><u></u>=
=C2=A0<u></u></p></div><div><p class=3D"MsoNormal"><u></u>=C2=A0<u></u></p>=
</div></div></div></div>_______________________________________________<br>
rer" target=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/healeys"; rel=3D"noreferre=
r" target=3D"_blank">http://www.team.net/pipermail/healeys</a> <a href=3D"h=
ttp://autox.team.net/archive/healeys" rel=3D"noreferrer" target=3D"_blank">=
http://autox.team.net/archive/healeys</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; target=3D"_blank">Healeys@autox.t=
eam.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; rel=3D"noreferre=
r" target=3D"_blank">http://autox.team.net/mailman/listinfo/healeys</a><br>
<br>
s/healey.nut@gmail.com" rel=3D"noreferrer" target=3D"_blank">http://autox.t=
eam.net/mailman/options/healeys/healey.nut@gmail.com</a><br>
<br>
</div></blockquote></div>
--000000000000301abb0625092452--
--===============3596593317536685076==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys
http://autox.team.net/archive/healeys
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============3596593317536685076==--
|