fot
[Top] [All Lists]

[Fot] Cylinder head freeze plug help

Subject: [Fot] Cylinder head freeze plug help
From: info at dieselperformanceparts.com (DPPI - Mark Craig)
Date: Thu, 3 May 2018 15:30:39 +0000
References: <0099CE4F-A206-492F-A6E2-A7B54B8DE270@icloud.com> <16325cca095-c8e-37505@webjas-vac094.srv.aolmail.net>
I have been watching this and am curious why do you?ll have so much pressure in 
the cooling system that it blows freeze plugs out. I have run Shelby?s, 
Mustangs and now Spitfires.
We use a 7-12 PSI cap, that?s not enough to blow a plug out.
Are you?ll using some high PSI cap or some such thing???

[http://dieselperformanceparts.com/media/mail/logo_small_dppi.png]<dieselperformanceparts.com>



Mark Craig
Diesel Performance Parts, Inc.
411 Allied Drive, Nashville, TN 37211
www.dieselperformanceparts.com<http://www.dieselperformanceparts.com/>

[http://dieselperformanceparts.com/media/mail/icon_social_facebook.jpg]<https://www.facebook.com/DieselPerformanceParts>
 [http://dieselperformanceparts.com/media/mail/icon_social_twitter.jpg] 
<https://twitter.com/PerfectDiesel>  
[http://dieselperformanceparts.com/media/mail/icon_social_googleplus.jpg] 
<https://plus.google.com/u/0/104451046659790804057/posts>  
[http://dieselperformanceparts.com/media/mail/icon_social_linkedin.jpg] 
<http://www.linkedin.com/company/diesel-performance-parts-inc->




Phone: 615-834-0066
Fax: 615-834-9923




From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of fubog1 via Fot
Sent: Thursday, May 03, 2018 6:39 AM
To: gblake58tr3 at icloud.com; jerryvv at roadrunner.com
Cc: fot at autox.team.net
Subject: Re: [Fot] Cylinder head freeze plug help

I routinely strap that rear plug or lock it in with a 10/32 and a flat washer 
folded in on either side.
Overkill... perhaps, but that sucker isn't coming out.
Glen



-----Original Message-----
Sent: Thu, May 3, 2018 3:33 am
Subject: Re: [Fot] Cylinder head freeze plug help
I had one pop out on me at the Sunday afternoon race of the Kastner cup at Road 
Atlanta a few years ago. I was bummed to miss out on the remaining laps so 
figured I did not want that to happen again.

When I pulled the head, I drilled and tapped to 10-32 holes each side of the 
rear freeze plug. After installing the new plug, I installed a bar that spans 
the plug and bolts to the head using the two trapped holes. In the center of 
the bar is a weld nut that I run a bolt through to put a little pressure on the 
freeze plug. Probably over kill, but Won?t be popping again.
Sent from my iPhone

It goes without saying that you should coat the edges with a good epoxy before 
you bonk it.
JVV

From: JAMES GRAY via Fot
Sent: Wednesday, May 2, 2018 11:12 AM
To: Jack Wheeler
Cc: FOT Triumph
Subject: Re: [Fot] Cylinder head freeze plug help

Jack,
The old freeze plug was found last night under my catch tank at the battery 
tray. It didn't have much of a ding in it
so I suspect it could have been flattened more/better when it was first put in.
Last night I was able to clear stuff as required to drill a 1/2" hole in the 
firewall directly behind the plug.
I already have a length of 1/2" solid round bar, tapered/rounded at the end in 
the hole just waiting for the new plug to arrive.
The round bar runs right under the dash. I'll be able to knock it in from the 
cockpit with a 3 pounder.
The car was running better than ever when it went, compression is at 200 psi on 
all four so at the moment
I don't have any reason to believe there are other problems. No evidence at all 
of water in the oil or cylinders.
However, once the plug is replaced and running again there will be detailed 
inspections once it's back up to running temp.
jim g
Hi Jim.  Consider this.  Pulling the head may give you the most correct fit, 
and also may be quicker, all things considered.  When I was racing, and had to 
pull the head at the race track, I could get it off and back on, new head 
gasket, and nuts torqued, in under an hour.  By the time you make clearance 
under the dash, and drive the plug in, possibly not aligned correctly, I'll bet 
you will have over an hour invested.  Good luck.

Jack

PS.  have you determined what caused the freeze plug to blow out?  The one time 
I had that happen at the race track, it was the result of a major cylinder head 
failure.  You may be looking at a bigger problem than just the freeze plug.




I used one of those expandable core plugs on a BMW 2002 and left it in for the 
next 60,000 miles with no sign of leaks.

Duncan


I've used a neoprene plug at the track to get by until I could pull the head.
Bill Newman
#44 GT6

----- Original Message -----
Sent: Tue, 01 May 2018 07:44:38 -0400 (EDT)
Subject: Re: [Fot] Cylinder head freeze plug help

Duncan,
I think that?s where I?m going next, the freeze plug is just about in line with
the bottom of the dash or close. The good thing is it blew the old plug 
completely out.
I just need to knock a new one in.
I?m pretty sure I can go under the dash and through with a piece of ? or even 
?? round
bar about 2? long which I can scrounge at work.
I?ll have to remove some stuff but still better than pulling the head.
jim


Sent: Tuesday, May 1, 2018 5:36 AM
Subject: Re: [Fot] Cylinder head freeze plug help


Can you drill a hole through the firewall and drive it out or yank it out that 
way?


Duncan




FoT
I was wondering if anyone has a clever method of putting in a cylinder head 
freeze plug without removing the head.
I was instructing at our drivers school this past weekend when it blew out.
I may have enough room between the firewall to use a short blunt air chisel
but I have my doubts so if anyone has a better one please let me know.
Thanks as always,
jim g


_______________________________________________

http://www.fot-racing.com

Archive: http://www.team.net/pipermail/fot

_______________________________________________

http://www.fot-racing.com

Archive: http://www.team.net/pipermail/fot

________________________________
_______________________________________________

http://www.fot-racing.com

Archive: http://www.team.net/pipermail/fot

_______________________________________________

http://www.fot-racing.com

Archive: http://www.team.net/pipermail/fot

_______________________________________________

http://www.fot-racing.com

Archive: http://www.team.net/pipermail/fot

-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/fot/attachments/20180503/230eb3d0/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.png
Type: image/png
Size: 13118 bytes
Desc: image001.png
URL: 
<http://autox.team.net/pipermail/fot/attachments/20180503/230eb3d0/attachment.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image002.jpg
Type: image/jpeg
Size: 2153 bytes
Desc: image002.jpg
URL: 
<http://autox.team.net/pipermail/fot/attachments/20180503/230eb3d0/attachment.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image003.jpg
Type: image/jpeg
Size: 2472 bytes
Desc: image003.jpg
URL: 
<http://autox.team.net/pipermail/fot/attachments/20180503/230eb3d0/attachment-0001.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image004.jpg
Type: image/jpeg
Size: 3083 bytes
Desc: image004.jpg
URL: 
<http://autox.team.net/pipermail/fot/attachments/20180503/230eb3d0/attachment-0002.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image005.jpg
Type: image/jpeg
Size: 2784 bytes
Desc: image005.jpg
URL: 
<http://autox.team.net/pipermail/fot/attachments/20180503/230eb3d0/attachment-0003.jpg>

<Prev in Thread] Current Thread [Next in Thread>