Can some one enlighten me on the Vacuum system?
Thanks!
Mike Mehl
________________________________
From: "n197tr4@cs.com" <n197tr4@cs.com>
To:
toodamnfunky@comcast.net
Cc: fot@autox.team.net
Sent: Monday, January 30,
2012 2:34 PM
Subject: Re: [Fot] Oversize split seal for TR4 engine
we had one
guy metalize his crank and put the scroll lines in the crank back
in.
i
suspect that metalizing and grinding back to OEM only will get the job done
with the VITON SEAL.
Of course I am a believer in the vacuum system, too.
Thanks Jim
Joe Alexander
A. R. E.
645 1st Street
Jesup, Iowa 50648
319.464.4711 (cell)
n197tr4@cs.com
-----Original Message-----
From:
toodamnfunky <toodamnfunky@comcast.net>
To: n197tr4 <n197tr4@cs.com>
Cc: fot
<fot@autox.team.net>; rkramer3 <rkramer3@austin.rr.com>
Sent: Mon, Jan 30,
2012 4:21 pm
Subject: Re: [Fot] Oversize split seal for TR4 engine
Can you
use Chris' seal without the scroll? I'm a big fan of the Viton seal.
jg
From: n197tr4@cs.com
To: rkramer3@austin.rr.com
Cc: fot@autox.team.net
Sent:
Monday, January 30, 2012 2:46:58 PM
Subject: Re: [Fot] Oversize split seal for
TR4 engine
Metalize seal diameter and regrind to OEM dimension and install
Christian
Marx' VITON SEAL.
Install vacuum system to crankcase, if you have
not already.
Joe Alexander
A. R. E.
645 1st Street
Jesup, Iowa 50648
319.464.4711 (cell)
n197tr4@cs.com
-----Original Message-----
From:
rkramer3 <rkramer3@austin.rr.com>
To: fot <fot@autox.team.net>
Sent: Mon, Jan
30, 2012 3:38 pm
Subject: [Fot] Oversize split seal for TR4 engine
I have
had my share of machine shop disappointments over the years but this
one
hurt.
I had two stock crankshafts cryo treated and reground with the
intention
of
building a lower rpm motor using Larry Young's camshafts and replacing the
crank in my son't TR4 racecar. At the time the machinist I had been using
went
out of business and I tried a guy that had been recommended by a couple of
Spitfire guys in my local club. Long story short, he screwed up the grind on
the
scroll seal and overcut it. I put the crank in the TR4 and trimmed the
seal a
little bit but the car leaks too much oil. Not very scientific, I know
but I
was
desparate. Before I start experimenting has anyone found on oversize
split
seal,
or split a seal on their own and could offer advice? I'd hate to
throw two
cranks in the metal bin.
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Donate: http://www.team.net/donate.html
Archive:
http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe:
http://autox.team.net/mailman/options/fot/n197tr4@cs.com
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Donate: http://www.team.net/donate.html
Archive:
http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe:
http://autox.team.net/mailman/options/fot/toodamnfunky@comcast.net
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Donate: http://www.team.net/donate.html
Archive:
http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe:
http://autox.team.net/mailman/options/fot/mike.mehl@yahoo.com
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
|