datsun-roadsters
[Top] [All Lists]

Re: [Roadsters] seat belts

To: <datsun-roadsters@autox.team.net>, <vulforge@aol.com>
Subject: Re: [Roadsters] seat belts
From: "Fred Schroeder" <roadster2@schroeder-family.us>
Date: Sat, 17 Dec 2011 01:19:17 -0600
NC is 3/8-16
NF is 3/8-24

I'm not familiar with 3/8-20.  Metric bolts perhaps?

Best regards,

Fred Schroeder
roadster2@schroeder-family.us
Home page: http://schroeder-family.us
NRA Life Member

Behold the superfluous. They are always sick. They
vomit their gall and call it a newspaper.
Friedrich Wilhelm Nietzsche   1844-1900
  ----- Original Message -----
  From: Gary and Cindy Ault
  To: datsun-roadsters@autox.team.net ; vulforge@aol.com
  Sent: Friday, December 16, 2011 9:19 PM
  Subject: Re: [Roadsters] seat belts


  Russell,

  Those threaded inserts are/were intended for seat belts.  My '66 1600 came
  with factory seat belts installed in those locations.  If I understand the
  laws correctly, seat belt were not required in imported cars until 1968.
  But, I suspect Nissan installed belts in all their cars headed for the US,
  and I wouldn't be surprised if Gary's car originally had belts.

  I wouldn't be surprised to find there are threaded inserts for the shoulder
  harness installed beginning with '67-1/2 on some of the earlier cars --
  under the vinyl.

  The bolts are 3/8-20.  (I just measured the bolts on a set of replacement
  belts I bought for my '67-1/2.)  I think that's National Fine.  (I know that
  5/16-18 is NC and 5/16-24 is NF, so 3/8-20 seems to make sense as NF.)

  Gary

  ----- Original Message -----
  From: <vulforge@aol.com>
  To: <datsun-roadsters@autox.team.net>
  Sent: Friday, December 16, 2011 4:25 PM
  Subject: [Roadsters] seat belts


  >I recently put belts in my early '67.  There are already threaded inserts
  > behind and beside the seats.  One pair is on the trans tunnel about 2" up
  > from
  > the floor right behind the seats.  The other is on the angled part of the
  > floor that sloes down from the package shelf to the floor toward the
  > outside
  > of the car.  I think theses bolt points may have been intended for the
  > roll
  > bar, but they work fine for seat belts.  I don't remember the thread
size,
  > might be 3/8 fine?
  >
  >
  > Russell Criswell
  > Vulcan's Forge
  > 3936 Broadway
  > Kansas City, MO
  > 64111
  >
  > 816-931-6303
  > 816-931-9378 fax
  > 877-531-1046 toll-free
  > www.vulcans-forge.com
  > ________________________________________
  >
  > datsun-roadsters@autox.team.net
  >
  > Donate: http://www.team.net/donate.html
  > Archive: http://www.team.net/archive
  > Forums: http://www.team.net/forums
  > Unsubscribe:
  > http://autox.team.net/mailman/options/datsun-roadsters/aultgc@att.net
  ________________________________________

  datsun-roadsters@autox.team.net

  Donate: http://www.team.net/donate.html
  Archive: http://www.team.net/archive
  Forums: http://www.team.net/forums
  Unsubscribe:
http://autox.team.net/mailman/options/datsun-roadsters/roadster2@schroeder-fa
mily.us
________________________________________

datsun-roadsters@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums


<Prev in Thread] Current Thread [Next in Thread>