G'day all,
Couldn't you cut a thread onto the back of the badges, and then screw them
on?
Cheers,
Steve
(needing to re affix his "Datsun" badge to the back - It's the only one I've
got, and people keep looking oddly at my baby to work out what it is!)
'68 2000 Solex
>From: Ryan Roswell Bird <BirdMan@myrealbox.com>
>Reply-To: Ryan Roswell Bird <BirdMan@myrealbox.com>
>To: datsun-roadsters@autox.team.net
>CC: haugchiro@moscow.com
>Date: Mon, 24 Sep 2001 05:41:15 +0000
>
>Bob,
> I think you are referring to the decal clips which were metal. I used
>Windshield Wiper Washer hose from a local AutoZone, cut 'em up to the right
>size, and they stay on nice and tight, no damage to the paint either. I
>brought the "D" from the front hood just to make sure the hose fit.
> Funny how if I were to purchase the clips, it would get rather
>expensive. A few feet of the rubber hose was just a buck or two.
>
>Good Luck, I'm in the middle of a slow moving Frame Off myself. (Slow
>primarily due to geographical issues.)
>
>Ryan Bird
>'67 1600
>Car - Santa Ana, CA
>Home - Tempe, AZ
>Work - Los Angeles, CA
>School - Glendale, AZ
>www.picturetrail.com/ryanrbird
>
> >>> R Haug <haugchiro@moscow.com> 09/23/01 08:58PM >>>
>Greetings all,
>First, thanks for all the replies on the original tire diameter.
>
>Second, the good news is that my 67.5 is now
>all black. Just painted it today. PPG base coat
>clear coat in black of course. I do have a couple
>(really 4) small runs. Not bad for never doing a complete
>paint job before. I can fix them when I cut and buff the
>finish. Now it is time to start to reassemble the body.
>
>Remember, I have been doing a frame off, and the body
>has been stripped of everything.
>
>My question is, did I read somewhere, where someone
>mentioned a replacement for the metal posts that hold
>the stainless trim on that are made of plastic? If so,
>what did they come on and is there an outlet for them.?
>
>Next, I will be working on the engine bay first, trying to
>put all of the little parts back on the firewall before I
>drop the body back on the frame. I know I need to
>fit the water drain hose, grommets, heater valve and probably the
>throttle shaft/rod or I won't be able to get to them
>since the engine is on the frame already. Is there anything else
>I should put back on the firewall before I set the body on
>the frame? Should the wiring harness be hooked to the starter.
>After hearing how difficult it is to get to that starter, just thought
>I should ask.
>
>Bob
>67.5
>Moscow, Idaho
>
>///
>/// datsun-roadsters@autox.team.net mailing list
>/// Send admin requests to majordomo@autox.team.net or go to
>/// http://www.team.net/cgi-bin/majorcool
>/// Send list postings to datsun-roadsters@autox.team.net
>///
>
>///
>/// datsun-roadsters@autox.team.net mailing list
>/// Send admin requests to majordomo@autox.team.net or go to
>/// http://www.team.net/cgi-bin/majorcool
>/// Send list postings to datsun-roadsters@autox.team.net
>///
>
_________________________________________________________________
///
/// datsun-roadsters@autox.team.net mailing list
///
|