I had a standard Alpine driveshaft shortened at a local shop. Just get the
proper overall length from someone who has one. I can give you a measurement
if you need it.
P
Sent from my iPad
> On Dec 24, 2013, at 4:06 AM, "Lauri Lehtinen" <lehtinen.lauri@kolumbus.fi>
wrote:
>
> A special shop made me a correct prop shaft using Mercedes, BMW and Ford
> shafts as raw material. European cars of 60s and 70s had only few
> different universal joints and splines plus bolt joints. Shaft was then
> friction-welded and balanced. Problem was to make a rear fixing plate,
> because OD & gearbox are from a later Humber.
>
> I have seen a series 2 Alpine with later Humber engine and OD box. It was
> fixed by moving whole engine forward, then cutting a hole for radiator to
> bring it forward too. It looked quite awful.
>
> Solenoid relay + switch I found from eBay.
>
> I have had problems with jumping gears, I hope I can fix it with new pilot
> bearing and engine and gearbox mounting rubbers.
>
> Merry Christmas for all of you!
>
>
>
> Ldhettdjd: jacranwell@aol.com [mailto:jacranwell@aol.com]
> Ldhetetty: 24. joulukuuta 2013 10:13
> Vastaanottaja: lehtinen.lauri@kolumbus.fi; bmounce@rcn.com;
> alpines@autox.team.net
> Aihe: Re: [Alpines] rear axle question
>
>
>
> Hi Lauri,
>
>
>
> The main thing is to make sure you have the O/D propshaft, which is shorter
> than the standard unit. Then you'll need to wire up the solenoid and
switch.
>
>
>
> Merry Christmas.
>
>
>
> Julian.
>
>
>
> -----Original Message-----
> From: Lauri Lehtinen <lehtinen.lauri@kolumbus.fi>
> To: 'Bill Mounce' <bmounce@rcn.com>; 'Alpine Discussion Group'
> <alpines@autox.team.net>
> Sent: Mon, 23 Dec 2013 21:54
> Subject: Re: [Alpines] rear axle question
>
> I have never seen any step-by-step guide to add an OD. I have one in place
> but engine still out. Is there any major pitfalls I should be aware of? And
> how to lengthen speedo cable, std is very tight when fitted to OD unit?
>
> -----Alkuperdinen viesti-----
> Ldhettdjd: alpines-bounces@autox.team.net
> [mailto:alpines-bounces@autox.team.net
> Ldhetetty: 23. joulukuuta 2013 16:28
> Vastaanottaja: Alpine Discussion Group
> Aihe: [Alpines] rear axle question
>
> Hello all,
>
>
>
> I just read the article in this month's Rootes Review about adding and O/D
> unit, and they listed two different rear axle ratios, and the resultant
> speeds v. revs. I always had these questions: how do I know which rear end
> I have, and why were there two different ones? At one point I thought one
> went with the O/D trans, the other with non O/D, but that made little
sense.
> Can anyone 'splain'?
>
>
>
> Thanks, Merry Christmas & Happy Holidays to all,
>
>
>
> Bill Mounce
>
>
>
> 1967 SV
> _______________________________________________
> Alpines@autox.team.net
> Donate: http://www.team.net/donate.html
> Suggested annual donation $17.25
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/alpines/lehtinen.lauri@kolumbus.fi
> _______________________________________________
> Alpines@autox.team.net
> Donate: http://www.team.net/donate.html
> Suggested annual donation $17.25
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/alpines/jacranwell@aol.com
> _______________________________________________
> Alpines@autox.team.net
> Donate: http://www.team.net/donate.html
> Suggested annual donation $17.25
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
http://autox.team.net/mailman/options/alpines/canisdog@aol.com
_______________________________________________
Alpines@autox.team.net
Archive: http://www.team.net/archive
|