Search String: Display: Description: Sort:

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*cutting\s+out\s+floorpans\s*$/: 7 ]

Total 7 documents matching your query.

1. Re: cutting out floorpans (score: 1)
Author: "Pat and Kammy Willems" <pwillems@cyberramp.net>
Date: Thu, 1 Oct 1998 19:08:21 -0500
You have already gotten some replies. I will add my $0.02 if that is OK. This may be obvious but I will state it anyway-- I recommend you do one side at a time and also make sure you have the door o
/html/spitfires/1998-10/msg00022.html (8,596 bytes)

2. Re: cutting out floorpans (score: 1)
Author: Barry Schwartz <bschwart@pacbell.net>
Date: Fri, 02 Oct 1998 06:18:53 -0700
** Yep, I had the same problem with mine. I even ordered the replacement tips etc. but it's just a shortcoming with the tool. This is however the best cutter for the job. I have replace (and removed
/html/spitfires/1998-10/msg00031.html (7,563 bytes)

3. Re: cutting out floorpans (score: 1)
Author: jak0pab@jak10.med.navy.mil (Bowen, Patrick A. RP2)
Date: Mon, 05 Oct 1998 09:29:45
Where can I find one of these and how much can I expect to pay? Patrick Patrick Bowen '79 Spitfire Jacksonville FL
/html/spitfires/1998-10/msg00073.html (7,885 bytes)

4. Re: cutting out floorpans (score: 1)
Author: "Pat and Kammy Willems" <pwillems@cyberramp.net>
Date: Tue, 6 Oct 1998 22:04:40 -0500
Order a catalog from http://www.eastwoodco.com/index.html My copy of the catalog shows P/N Desc Price 19017 3/8" Professional Spot Weld Cutter $17.99 19068 Spot Weld Cutter Assy (has center guide pin
/html/spitfires/1998-10/msg00145.html (7,870 bytes)

5. cutting out floorpans (score: 1)
Author: jak0pab@jak10.med.navy.mil (Bowen, Patrick A. RP2)
Date: Wed, 30 Sep 1998 14:46:30
Okay, so I am now tediously beginning the job of removing my floor pans to be replaced. i have started drilling out some of the spot welds and thought I should stop and ask some advice. Is it bad to
/html/spitfires/1998-09/msg00582.html (7,358 bytes)

6. Re: cutting out floorpans (score: 1)
Author: SUCHAK <suchak@mediaone.net>
Date: Wed, 30 Sep 1998 22:11:51 -0400
Patrick: What you need is a spot weld cutter, sort of a hollow centered drill that cuts *around* the spot weld, leaving the welded center attached to the intact panel below, which you then grind off.
/html/spitfires/1998-09/msg00595.html (7,185 bytes)

7. Re: cutting out floorpans (score: 1)
Author: tomomalley@hey.net (Tom O'Malley)
Date: Thu, 01 Oct 1998 02:33:01 GMT
Patrick writes... Yeah...try not to do this if you an avoid it. As John says, there's a special spot weld cutter you can buy that will make this task easier. Eastwood sells two types...I one I tried
/html/spitfires/1998-09/msg00596.html (7,409 bytes)

Current List: 1 - 7
Page: [1]
This search system is powered by Namazu