Mail Archive Search: <+from:agraham@execulink.com>

Results:

References: [ +from:agraham@execulink.com: 115 ]

Total 115 documents matching your query.

81. [TR] TR2/3 windshield frame. (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Mon, 10 Sep 2012 11:23:15 -0400; Hello List: Trying to get a better fit on the body to windshield frame seal, took the shield off to install a new seal. Turns out a couple of the screws securing the bottom frame to the top and sides; /html/triumphs/2012-09/msg00095.html (10,544 bytes)
82. [TR] TR2/3 oil pressure question (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Sun, 16 Sep 2012 18:33:18 -0400; Hello List: Concerned about the oil pressure in my 'fresh' engine in the '2. Right on idle, seems to hold at around 40 - 50 lbs. on a cold engine. When hot and revved, climbs only slightly. I changed; /html/triumphs/2012-09/msg00139.html (10,446 bytes)
83. [TR] TR2 - Tenax fasteners (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Wed, 19 Sep 2012 18:00:46 -0400; Hello List: A question about the Tenax fasteners on my '2 project. Moving to the more 'fun' stuff and finishing up the interior. Wondering about the Tenax pegs. In my disassembly I neglected to separ; /html/triumphs/2012-09/msg00174.html (10,386 bytes)
84. [TR] TR2/3 glove box mounting (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Wed, 19 Sep 2012 22:07:57 -0400; Hello List: Can anyone help with the glove box mounting - especially the rear "L" shaped bracket? Again, not sure where this bracket fastens to the under dash. I assume the threaded bolt portion exte; /html/triumphs/2012-09/msg00183.html (10,155 bytes)
85. [TR] Heat insulation material - installation (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Thu, 27 Sep 2012 10:49:30 -0400; Hello List: Just picked up some of the foil backed heat insulation to finish off the interior of my '2 project. The material is felt backed by a shiny aluminum foil. First and obvious question is whi; /html/triumphs/2012-09/msg00250.html (11,119 bytes)
86. Re: [TR] TR3 steering column and gearbox mount (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Sat, 24 Nov 2012 12:45:54 -0500; Hello Randall &List: Just wondering about the steering column mount that Randall identified in his photo. Was it an addition a bit later in the production run? I have a very original (and I think unm; /html/triumphs/2012-11/msg00148.html (8,531 bytes)
87. [TR] TR2/3 seat rails. (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Tue, 08 Jan 2013 20:52:49 -0500; Hello List: Trying to sort out the miscellaneous pieces I have to cobble together the seat rails and adjusters for my '2. I'm assuming that the TR2 and 3. 3A seat rails are similar. Are the adjuster; /html/triumphs/2013-01/msg00095.html (8,152 bytes)
88. [TR] TR2/3 hood hinges (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Thu, 17 Jan 2013 16:25:33 -0500; Hello List: Re-installing my newly painted hood hinges on the '2 and I didn't remember to mark the hinges right or left. They appear to slightly "toe in" or "toe out" with respect to the longer hood; /html/triumphs/2013-01/msg00196.html (8,369 bytes)
89. [TR] TR2/3 Badge fastening (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Mon, 21 Jan 2013 16:43:51 -0500; Hello List: Wondering what techniques listers have used to fasten the badges (& letters) to the front clip and rear deck (TR2). I have used the pegs on the backside of the badge and the "spring clips; /html/triumphs/2013-01/msg00251.html (8,550 bytes)
90. [TR] Battery trickle charger (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Mon, 28 Jan 2013 19:53:02 -0500; Hello List: My "el cheapo" 750 mA battery charger just bit the dust. Second one in a few years to fail. Purchased them from our local/national auto supply store (Canadian Tire). Just wondering if the; /html/triumphs/2013-01/msg00324.html (9,046 bytes)
91. [TR] TR2/3 - stator tube leaking. (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Sat, 04 May 2013 14:43:36 -0400; Hello List: Dealing with some of the "finishing touches" on my long standing TR2 project and struggling with a leaking stator tube nut/ferrule at the end of the steering box. Have tried a new nut and; /html/triumphs/2013-05/msg00030.html (8,219 bytes)
92. [TR] TR2/3 emerg. brake boot (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Wed, 29 May 2013 19:51:23 -0400; Hello List: Puzzling over some of the trim issues with my '2 project. Does the emerg. brake handle boot and mounting flanges get screwed directly to the floor pan, then the carpet fitted over them? S; /html/triumphs/2013-05/msg00345.html (8,360 bytes)
93. [TR] TR2/3 hood support rod (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Thu, 06 Jun 2013 18:24:47 -0400; Hello List: Just puzzling about the hood support rod. Can someone let me know how it is fastened to the front lip of the hood? Just acquired one and no hardware - have two small screw/ bolt holes fla; /html/triumphs/2013-06/msg00077.html (8,043 bytes)
94. [TR] TR2 seat installation & removal ? (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Sat, 06 Jul 2013 18:43:48 -0400; Hello List: I have a mid production '2 that is finally seeing the road very soon (thanks to the list!!) and puzzling over the seat installation. Don't recall how I removed the seats these many years; /html/triumphs/2013-07/msg00104.html (8,330 bytes)
95. [TR] TR2 - very stiff choke cable (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Thu, 11 Jul 2013 10:29:31 -0400; Hello List: I think this has been visited before, but having a real problem with the chokes on my rebuilt SU's (H4). Can't get the cable to even budge the chokes. Even pulled the knob off the cable w; /html/triumphs/2013-07/msg00133.html (8,482 bytes)
96. [TR] TR2/3 rear cross-member repair (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Tue, 16 Jul 2013 19:24:07 -0400; Hello List: A good friend has recently become a TR3 owner and while looking over the car a bit more carefully, he noticed that the rear cross-member that supports the rear spring mount has rusted pre; /html/triumphs/2013-07/msg00184.html (8,287 bytes)
97. [TR] TR2/3 - oil pressure adjustment (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Fri, 02 Aug 2013 12:21:19 -0400; Hello List: Just trying to straighten out some of the issues with my '2 project that is finally ready for the road. My '2 had the early filter head with the partial full-flow feature. I changed it ou; /html/triumphs/2013-08/msg00005.html (8,533 bytes)
98. [TR] TR2/3 - transmission tunnel install (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Thu, 22 Aug 2013 21:35:15 -0400; Hello List: After running my '2 project for several weeks getting up the nerve to install the transmission tunnel. Have delayed this in anticipation of any issues with the o/d or who knows? It has be; /html/triumphs/2013-08/msg00216.html (8,765 bytes)
99. Re: [TR] Inquiring minds want to know. (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Sat, 26 Oct 2013 13:49:00 -0400; Hello List: On the TR3 badge question, on my '2 I have a similar badge, approx. the same size and font that reads: "Triumph TR2". It is on the rear deck centered between the spare tire cover and trun; /html/triumphs/2013-10/msg00140.html (7,861 bytes)
100. [TR] Post motor rebuild re-torque (score: 1): Author: Angelo Graham <agraham@execulink.com>; Date: Mon, 11 Aug 2014 18:44:11 -0400; Hello List: Just wondering about how many miles following a motor rebuild (TR 2-4) should re-torquing of head & setting of valve clearances take place? Should any other re-torquing be done as well? M; /html/triumphs/2014-08/msg00045.html (8,389 bytes)

Current List: 81 - 100
Page: [1] [2] [3] [4] [5] [6]