Mail Archive Search: <+from:DENKLEMM@aol.com>

Results:

References: [ +from:DENKLEMM@aol.com: 61 ]

Total 61 documents matching your query.

21. P type exhaust system (score: 1): Author: DENKLEMM@aol.com; Date: Mon, 9 Jun 2003 22:52:23 EDT; Hi All, Is anybody suppling the PA exhaust system in the USA? Or must I order it from the UK? Thanks Dennis Klemm PA1516 /// unsubscribe/change address requests to majordomo@autox.team.net or try ///; /html/mg-mmm/2003-06/msg00009.html (6,778 bytes)
22. P Type Gas Tank (score: 1): Author: DENKLEMM@aol.com; Date: Thu, 19 Jun 2003 20:08:56 EDT; Hi All, I have located a new replacement gas tank for my PA. However, my old rusted out tabk measures 27 1/2" wide and the new tank measures 30 3/8" wide. Which is right? Or is the new tank for somet; /html/mg-mmm/2003-06/msg00026.html (6,994 bytes)
23. P type engine (score: 1): Author: DENKLEMM@aol.com; Date: Tue, 6 May 2003 09:01:14 EDT; Hi All, The clutch spigot bearing (ball bearing mounted to the flywheel) appears not to be lubricated. Is this correct or should a small amount of grease by applied during assembly? What is the diffe; /html/mg-mmm/2003-05/msg00011.html (7,196 bytes)
24. Jerry Felper (score: 1): Author: DENKLEMM@aol.com; Date: Sun, 11 May 2003 15:01:09 EDT; Does anybody have an e-mailaddress for Jerry Felper? Thanks Dennis PA1679 Janesville, WI /// unsubscribe/change address requests to majordomo@autox.team.net or try /// http://www.team.net/cgi-bin/ma; /html/mg-mmm/2003-05/msg00022.html (6,884 bytes)
25. P type oil filter (score: 1): Author: DENKLEMM@aol.com; Date: Sun, 11 May 2003 15:05:05 EDT; I think I have most of the right parts for the oil filter. Can someone tell me the correct length of the felt oil filter and the correct length of the spring on top of the pressure relief valve? The; /html/mg-mmm/2003-05/msg00023.html (6,950 bytes)
26. MG PA Head (score: 1): Author: DENKLEMM@aol.com; Date: Fri, 23 May 2003 14:40:16 EDT; Hi All, I've worked on a lot of different MGs and restored quite a few, but this PA is by far the hardest! Here is the problem. The head was cleaned, cracked tested and new seats and guides installed; /html/mg-mmm/2003-05/msg00046.html (8,295 bytes)
27. MGPA Stop light switch (score: 1): Author: DENKLEMM@aol.com; Date: Sat, 31 May 2003 16:08:26 EDT; Hi All, I assume the stop light switch mounts to the underchassis pan. Does it connect to the brake pedal or to the rotating brake shaft and where? I don't see a hole in either. I assume it connects; /html/mg-mmm/2003-05/msg00054.html (7,111 bytes)
28. P type engine sleeves (score: 1): Author: DENKLEMM@aol.com; Date: Sat, 8 Mar 2003 21:35:26 EST; Hi All, Any suggestions on where to purchase piston sleeves for my PA? Thanks Again, Dennis PA1516 /// unsubscribe/change address requests to majordomo@autox.team.net or try /// http://www.team.net/c; /html/mg-mmm/2003-03/msg00000.html (6,610 bytes)
29. PA Block (score: 1): Author: DENKLEMM@aol.com; Date: Mon, 17 Mar 2003 18:00:07 EST; Hi All, My machine shop has informed me that I need a different block for my PA. Anyone have a block for sale or know where there is one? Thanks Dennis Klemm PA1518 minus block Janesville, WI /// uns; /html/mg-mmm/2003-03/msg00017.html (7,390 bytes)
30. PA Block (score: 1): Author: DENKLEMM@aol.com; Date: Tue, 18 Mar 2003 14:01:26 EST; Hi All, Here is the story of my PA block. Machine shop #1, ultrasonic measure the cylinder walls and determined that the block could be bored to 60 mm and still have a wall thickness of .250" They su; /html/mg-mmm/2003-03/msg00022.html (8,469 bytes)
31. P Type rear axle & Brake (score: 1): Author: DENKLEMM@aol.com; Date: Sun, 9 Feb 2003 18:22:09 EST; Hi All! My PA came to me with what I think is hydraulic TC brakes. I have purchased new backing plates, new brake drum and new axle shafts. The front brakes went on fine. When I assemble the rear bra; /html/mg-mmm/2003-02/msg00027.html (7,884 bytes)
32. P type rear axle bearing carriers (score: 1): Author: DENKLEMM@aol.com; Date: Mon, 10 Feb 2003 22:19:08 EST; Hi All, Anybody got a spare set of rear axle bearing carriers that they would like to sell? Thanks Dennis PA1518 /// unsubscribe/change address requests to majordomo@autox.team.net or try /// http://; /html/mg-mmm/2003-02/msg00033.html (6,922 bytes)
33. PA with supercharger (score: 1): Author: DENKLEMM@aol.com; Date: Tue, 18 Feb 2003 16:00:36 EST; Hi All, Does anybody have any information on using an Arnolt supercharger on a PA? I have an opportunity to buy one, but have no idea what I would be getting into. Thanks Dennis Klemm Wisconsin PA151; /html/mg-mmm/2003-02/msg00042.html (7,226 bytes)
34. Re: rear trunnion retaining nut (score: 1): Author: DENKLEMM@aol.com; Date: Wed, 4 Dec 2002 08:59:21 EST; Both nuts are left hand thread. They are available from Sports & Vintage, Moss and Barry Walker. Cheers, Dennis PA1516 /// unsubscribe/change address requests to majordomo@autox.team.net or try ///; /html/mg-mmm/2002-12/msg00002.html (7,642 bytes)
35. More PA Clutch (score: 1): Author: DENKLEMM@aol.com; Date: Wed, 11 Dec 2002 09:45:45 EST; Hi All, Can anybody tell me what the thickness is of a new clutch disc for the PA? Thanks Dennis PA1518 /// unsubscribe/change address requests to majordomo@autox.team.net or try /// http://www.team.; /html/mg-mmm/2002-12/msg00016.html (6,848 bytes)
36. Beware motolit.com (score: 1): Author: DENKLEMM@aol.com; Date: Thu, 12 Dec 2002 15:07:06 EST; Hi All, ON November 15th I ordered a "in stock" MG Book from motorlit.com. They billed my credit card that same day. Repeated e-mails got no response. On December 2nd I filed a claim with the credit; /html/mg-mmm/2002-12/msg00026.html (7,411 bytes)
37. PA Axle shafts and hub (score: 1): Author: DENKLEMM@aol.com; Date: Thu, 7 Nov 2002 22:09:22 EST; Hi All, I'm looking for new or good used axle shafts with hubs for the PA. Are there any available in the USA or do I need to order from England. Thanks Dennis Klemm PA1518 /// unsubscribe/change add; /html/mg-mmm/2002-11/msg00017.html (6,906 bytes)
38. MG PA piston rings (score: 1): Author: DENKLEMM@aol.com; Date: Thu, 14 Nov 2002 09:26:23 EST; I have been told that replacement piston rings are from a Honda motorcycle. Anybody have any further information on this. Thanks, Dennis Klemm PA1518 /// unsubscribe/change address requests to majord; /html/mg-mmm/2002-11/msg00024.html (7,714 bytes)
39. MG PA pistons (score: 1): Author: DENKLEMM@aol.com; Date: Thu, 14 Nov 2002 12:05:11 EST; Hi All Just heard from the machine shop again....different tune. The pistons that are currently in the engine measure 2.359", slightly under 60 mm. Does this mean that these are PB pistons? What is t; /html/mg-mmm/2002-11/msg00026.html (7,965 bytes)
40. Re: MG PA pistons (score: 1): Author: DENKLEMM@aol.com; Date: Thu, 14 Nov 2002 14:31:45 EST; Let me try to be clearer. The block that came out of my PA is a single breather. The pistons that came out of it measure 2.359" (60 mm is 2.362" & 57 mm is 2.244") My pistons are already .118 oversiz; /html/mg-mmm/2002-11/msg00030.html (8,021 bytes)

Current List: 21 - 40
Page: [1] [2] [3] [4]