OK since AOL is being all stuffy ,, High and mighty and just plain generally messed up... I have had enough of AOL ..changing internet providers is most delightful, please put me on the list under a
I have for sale three trucks first is a very desireable 59 fleet side shorty, NO MOTOR and transmission, was orignally a v-8 with automatic,two tone paint job, had all the s/s trim at one time,soe tr
Once had an 55 truck that had a lot of sludge in it,, I decided id try to rinse some of the gunk out of it,,, some old mechanic told me to put one quart of oil to 4 quarts of diesel and let the engin
the cigarette ligher only requires a fused wire from a 12 volt source cannectet to the center terminal to work , I dont know the amps your going to need for the fuse, the body ( base) of the lighter
Ok you have my curiosity,,, whats this talk about a ship engine,, Send me a link or pic thanks' Richard oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
If you use the right hose and routed it properly its not a problem,, hose is used on the transmission cooler lines by the factory on many cars and trucks ,,but usually for only short distances for fl
The clutch alignment tools usually enexpensive at the parts stores some are made of wood other of plasitc. Recently ive seen new and rebuilt clutch kits coming with plastic ones that become part of y
Interesing Idea,,Ive worked on the F*&d ONES i HATE THEM,, ON THE OTHER HAND the 4.0 AMC/Jeep are fairly easy to work on,still not that fond but much cleaner..let US know if you end up trying one out
I seen this on ebay incase anyone is has an interest I am posting it here. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=2406008403&category=6245 Richard oletrucks is devoted to Chevy
I went back and took a look at it again too.. these are my observations, the seller is not posting the vin # so the year is not certain,57 model year is very questionable, the steering wheel does app
this is what ive found you need,, first you cant use the floor pedal for the starter,, you will need a v-8 starter for std shift that will fit the bell housing preferably one that fits TF trucks so y
Ive been reading what other have to say, Good post all good advice, take all into consideration,,check and make sure the thin Oil control rings are correctly installed on the ledge of the spring spac
You may have air in the system again or have lost brake fluid some where,, Check closely and make sure the bleeder valves are tight and not leaking, check the fluid level, look for leaks in ALL the l
My 59 GMC 630 series has a 503 Cu GMC inline 6 cylinder engine in it,,the engine block is two pieces bolted together,, the upper cylinders section is bolted to the lower crancase section,,,its quite
1972 and newer chevy small block heads had hardened seats for running unleaded gas, unless the 327 you have is a hi compression engine you shouldnt have any problem running unleaded gas, performance
I agree with the other too on what to look for on the ignition and gas,, now as far as it not moving while in neutral,, if the car has been setting a long time in a moist environment the brakes may b
Does anyone out ther have a wiring diagram they care to share that tells me how to wire up a factory Sun tach with the transmitter box for a 55 GMC Thank you Richard Scott 57 cameo 55-59 mixed breed
The best way that I have found is to cut the rusty metal out and weld in new patch panels either from a parts source or metal cut from a donor ,, Ive used lead and have brazed in the past ,,Ive found
I received this today from a car post I subcribe to. Beware and be careful. Ricahrd Scott The following scam was received at Team Chevelle and confirmed via email with 'Jaye' who took the time to ale