Here's a better photo.
> On August 14, 2018 at 11:57 AM Kenneth Knight <kknight at klaenv.com> wrote:
>
>
> All good advice from Dave. On thing to remember in the fit is the cover, it
> does take a bit of room. If you have a back that is not perfect (go figure
> a Vintage car driver could have a back problem) Pegasus sells a very dense
> special foam padding that can be placed under the cover. You can put it
> under your bony butt and at the small of the back to cushion the shock and
> pressure from the belts. It can also be used on the sides to make that fit
> just perfect.
>
> Underneath the car I have plates that tie that seat into the frame. There
> are lots of ways to do this but just putting a fender washer under the
> bracket bolts is NOT enough. Don't forget to tie the back of the seat to
> roll bar. In an ideal situation that is a bar crossing just about the
> height of your shoulder blades and this is the perfect mounting spot for the
> shoulder belts and the seat brace.
>
> Ken
>
> -----Original Message-----
> From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of DAVE HOGYE via
> Fot
> Sent: Tuesday, August 14, 2018 8:16 AM
> To: Steven Belfer via Fot; Todd Redmond; Steven Belfer
> Subject: Re: [Fot] Race Seat
>
> Good tips and suggestions, Steve.
> Todd, when I installed my Kirkey Vintage seat, as Steve suggests, I placed
> the seat low and wore my helmet to take some measurements. I wanted to be
> below the top of my roll bar and my bar fits under the factory hard top, so
> the height limit was known and set.
> I also modified the seat. I needed arm length but less leg length. When I
> tilted or reclined the back to a comfortable arm length, the seat bottom
> reduced leg extension needed for full clutch depression. I cut the seat to
> get more recline without effecting the bottom and leg position. It was an
> easy modification. I made a aluminum fill plates and had them welded in
> place. I also moved the steering wheel closer to the dash to give more arm
> extension. I spent a lot of time getting it all perfect for me.
> There are optimal leg and arm positions. Bent arms, never fully extended
> and when the clutch is fully depressed, your leg should not press on the
> seat bottom and impede movement, but could lightly touch. I learned this in
> 1982 when I bought Bob Bondurant's first book of high performance driving.
> The Kirkey seats come in different widths. Get one that fits relatively
> snug. Measure yourself in the seated position. If you have to you can send
> it back until you get the best fit.
> I thought the Vintage seat looks best without the head rest, but then you
> have to build a rest into your roll bar. Of course having the head rest
> extension solves this issue.
> I like that the Kirkey seats have a snap-in cover and inexpensive. I also
> added a little lumbar padding under the cover.
> Dave H.
>
> > On August 13, 2018 at 4:02 PM Steven Belfer via Fot <fot at autox.team.net>
> wrote:
> >
> >
> > Hi Todd,
> >
> > I fit a Kirkey upright seat in my TR3. I probably had it in and out of
> there 10 times and had the seat modified a bunch of times to get it right.
> I also had the cage re-worked to fit the seat and and give me protection on
> the left-side. I had the Kirkey seat-cover modified at an upholstery shop
> to fit the changed seat. I also added some custom foam lumbar-support
> pieces to the seat cover. The trick is to get the seat as low as possible
> in the car, then lean it back just right for your comfort. Test it while
> wearing your helmet and Hans device.
> >
> >
> > ~STEVE
> >
> >
> >
> > > On Aug 13, 2018, at 6:05 AM, Todd Redmond via Fot <fot at autox.team.net>
> wrote:
> > >
> > > Friends!
> > >
> > >
> > > I'm looking for recommendations for a race seat for the TR3.
> > > What are you using?
> > >
> > >
> > > Thanks
> > > Todd Redmond
> > > 1958 TR3a
> > > _______________________________________________
> > > fot at autox.team.net
> > >
> > > http://www.fot-racing.com
> > >
> > > Donate: http://www.team.net/donate.html
> > > Archive: http://www.team.net/pipermail/fot
> > > Unsubscribe/Manage:
> http://autox.team.net/mailman/options/fot/steve at artwithcars.com
> > >
> > >
> >
> > _______________________________________________
> > fot at autox.team.net
> >
> > http://www.fot-racing.com
> >
> > Donate: http://www.team.net/donate.html
> > Archive: http://www.team.net/pipermail/fot
> > Unsubscribe/Manage:
> http://autox.team.net/mailman/options/fot/dlhogye at comcast.net
> >
> >
> _______________________________________________
> fot at autox.team.net
>
> http://www.fot-racing.com
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/fot
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/fot/kknight at klaenv.com
>
>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: roll cage mount detail.JPG
Type: image/jpeg
Size: 182522 bytes
Desc: not available
URL:
<http://autox.team.net/pipermail/fot/attachments/20180814/ec4d96b1/attachment.jpe>
|