A web search says that the 4100 only has a full-time (not ported) vacuum port
on the choke side at the base of the carb. The OEM fitment had a screw-in hard
line going to the distributor; you might have to fab a fitting (take a 1"
piece of brake line and use a thread die to put some appropriate threads on
it, then screw that in with some blue loctite) so you can use it with a rubber
line. One reference I found says the thread is 1/8" pipe, if that's the case
you can get a brass fitting that goes from 1/8" pipe to 1/8" or 5/32" barb at
any decent plumbing or car parts store.
Theo
From: Joel Martin [mailto:jmartiniii@yahoo.com]
Sent: April 18, 2013 8:35 AM
To: Tiger List Serve; Smit, Theo; Ron Fraser
Subject: RE: [Tigers] Thermostat Housing and Right Angle oil filter adapter
Summit carries the nipple AAF-ALL92003 or Ford Number F1AZ6890B, thanks Theo,
for $6.59 which is ~1" on block side and 3/4" - 16 on oil adapter side. I
bought the Ford adapter M-68801-A50 as suggested on Tiger United site for
$79.95. Hope this nipple works. I really wanted to use the remote oil filter
set up but hose's were a challenge and cost prohibitive.
Scott Drake parts from Summit carries the spark plug wire separators, thanks
Ron, B8Q-12297-A for $1.93 and B6A-12297-A for $3.93.
Scott Drake parts from Summit references a different part number for the
thermostat housing C50E-8592-A for $17.97 instead of the C30Z-8594-B, thanks
Ron, but appears close as the angle is not a 90 degree like Ford part number
M-8592-M-90 for $33.95 which is a 90 degree.
You guys are keeping me moving. Clutch bled, waiting on booster to come back
from rebuild, Petronix distributor and coil to be installed, fuel and brake
lines run, - no fuel from refurbished tanks thru fuel pump though - always a
challenge. With the SS headers, will need to change choke to electric or go
to manual as no heat tube connections with headers unless someone has a
different idea for a heat tube alternative?
Not sure where on the Autolite 4100 carburetor to connect the ported vacuum
from the distributor to the carb though - any Ideas?
Thanks
Joel Martin
--- On Wed, 4/17/13, Smit, Theo
Subject: RE: [Tigers] Thermostat Housing and Right Angle oil filter adapter
Date: Wednesday, April 17, 2013, 3:43 PM
Google is your friend...
F1AZ6890B
Apparently this part is about $8.66 at your local Ford parts counter.
Theo
> -----Original Message-----
> From:
tigers-bounces@autox.team.net<http://us.mc1647.mail.yahoo.com/mc/compose?to=t
igers-bounces@autox.team.net> [mailto:tigers-
>
bounces@autox.team.net<http://us.mc1647.mail.yahoo.com/mc/compose?to=bounces@
autox.team.net>] On Behalf Of Joel Martin
> Sent: April 17, 2013 1:07 PM
> To: Tiger List Serve
> Subject: [Tigers] Thermostat Housing and Right Angle oil filter adapter
>
> All
>
> Does anyone know a part number of correct thermostat housing? Does it
> have just one nipple for a 66 MK 1A 289 motor? I will be installing
> the heater core.
>
> Also, I purchased the FMS-M-6880-A50 90 DEGREE OIL FILTER
> ADAPTOR. This
> requires a nipple adapter that goes into the block and then into the
> bolt of the adapter. In checking with Summit, they said it was 3/4"
> x16 on both sides. Apparently not, anyone know the correct nipple to
> purchase with part number aaa x size on the block side and 3/4 x 16 on
> the adapter side.
>
> Thanks
> Joel Martin
tox.team.net>
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
> http://autox.team.net/mailman/options/tigers/theo.smit@dynastream.com
>
>
________________________________
CONFIDENTIALITY NOTICE: This email and any attachments are for the sole use of
the intended recipient(s) and contain information that may be confidential
and/or legally privileged. If you have received this email in error, please
notify the sender by reply email and delete the message. Any disclosure,
copying, distribution or use of this communication (including attachments) by
someone other than the intended recipient is prohibited. Thank you.
________________________________
CONFIDENTIALITY NOTICE: This email and any attachments are for the sole use of
the intended recipient(s) and contain information that may be confidential
and/or legally privileged. If you have received this email in error, please
notify the sender by reply email and delete the message. Any disclosure,
copying, distribution or use of this communication (including attachments) by
someone other than the intended recipient is prohibited. Thank you.
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/mharc@autox.team.net
|