I've sent Kris a message thru the SCCA bulletin boards asking him to email me
with his contact info. I don't have his email directly.
--- On Sun, 9/28/08, Matt Hagopian <mhagopian@hoppetool.com> wrote:
> From: Matt Hagopian <mhagopian@hoppetool.com>
> Subject: Re: [Spridgets] john , NJMP in millville info?
> To: soavero@yahoo.com
> Cc: "David Lieb" <dbl@chicagolandmgclub.com>, "Spridget List"
><spridgets@autox.team.net>
> Date: Sunday, September 28, 2008, 1:37 AM
> Do you or anyone else on this site know about the specs of
> the internals of
> this engine? bud provided a list, but the list didnt
> contain information
> like what model cam it was, he listed APT scatter pattern.
> also what make of
> pistons, compression ratio.. he said on the site 12.5-13:1
> Im not sure
> exactly what he meant by that. valves are ok. i found out
> that all of the
> valves were too long.. they were shortened and now running
> much better. also
> my grandfather put a 50 amp alt from a suzuki on it because
> the alt was
> gone. if anything has been done to the crank? rods? this is
> all useful info
> to us that wasnt provided.
>
> OR
>
> If anyone has Kris Larsens contact information, this would
> be equally as
> helpful!
> Thanks guys!
>
> On Thu, Sep 25, 2008 at 7:12 PM, Ron Soave
> <soavero@yahoo.com> wrote:
>
> > Guys, guys, guys....
> >
> > This motor was bulletproof for years before Matt got
> the car when Kris
> > Larsen and Bud had it. The car had an SPVP4, I think.
> A valve bound and
> > stuck open, 99%.
> >
> > Ron
> >
> >
> > --- On Thu, 9/25/08, Matt Hagopian
> <mhagopian@hoppetool.com> wrote:
> > > i just looked on his website, you were right,
> re-keyed to
> > > 102 degrees. cam
> > > is an APT scatter...? no model number mentioned.
> > > beside this.. I have a 1.5 high lift rockers
> (that have a
> > > small crack in
> > > them) anyone have any suggestions which rocker to
> use?
> > >
> > > On Thu, Sep 25, 2008 at 1:43 PM, David Lieb
> > > <dbl@chicagolandmgclub.com>wrote:
> > >
> > > > >... Way too
> > > > > many variables involved to make an
> assumption on
> > > what the cam timing
> > > > > should be with only one piece of the
> puzzle, and
> > > I stand corrected.
> > > >
> > > > Are we allowed to say things like that on
> this
> > > List????
> > > >
> _______________________________________________
> > > > Support Team.Net
> http://www.team.net/donate.html
> > > >
> > > > You are subscribed as
> mhagopian@hoppetool.com
> > > >
> > > > http://www.team.net/archive
> > > >
> > > >
> http://autox.team.net/mailman/listinfo/spridgets
> > > >
> > >
> > >
> > >
> > > --
> > > Sincerely,
> > >
> > >
> > > Matt Hagopian
> > > _______________________________________________
> > > Support Team.Net http://www.team.net/donate.html
> > >
> > > You are subscribed as soavero@yahoo.com
> > >
> > > http://www.team.net/archive
> > >
> > > http://autox.team.net/mailman/listinfo/spridgets
> >
> >
> >
> >
>
>
> --
> Sincerely,
>
>
> Matt Hagopian
_______________________________________________
Support Team.Net http://www.team.net/donate.html
http://www.team.net/archive
http://autox.team.net/mailman/listinfo/spridgets
|