Kvach;
Well, I usually buy Hylomar in a tube and (most of the time) remember to put
the cap back on. Of a can of Hylomar has gotten too stiff to use, add a
little MEK to thin it back down.
Regards, Neil Tucson, AZ
-----Original Message-----
From: Salt Hawk [mailto:salthawk@coldreams.com]
Sent: Wednesday, September 04, 2002 9:55 PM
To: Doug Anderson; Albaugh, Neil; land-speed@autox.team.net
Cc: av8ford@sonic.net; saltcircus@mcn.net; chopt32@aol.com;
Capecod626@aol.com; bjd@pdqmfg.com; tinshed@ozemail.com.au;
whodaky@sympac.com.au; pyramid62@aol.com; Dkfowlermontana@aol.com;
hastingsv@aol.com; fah60@aol.com; newf4me@noln.com; holleran@sover.net;
robere@xensei.com; jungbec@aol.com; k2bdiana@bcn.net;
thechipcutter@aol.com; mkamm@juno.com; bellytk@nh.ultranet.com;
mzappulla@stny.rr.com; Dgasbag@aol.com; radbruch@sandpoint.net;
ynst@netzero.net; drichard@stny.rr.com; JAKENLOUANN3239@aol.com;
lsaltsman@telenet.net; neatoldstuff@webtv.com; rodtech@mindspring.com;
squarerollbars@yahoo.com; dspadaro@albany.net; Zulk62@aol.com
Subject: Re: Hylomar sealant
The real question about this stuff is how do you keep it from
going bad after you open the can and use a little of it Kvach
> Really,,,, where might we be able to purchase this stuff. It sounds
really
> really good! I'd like to try it for my pesky rottenchester 3 deuces that
> are forever leakers LOL!
>
> Thanks Neil, "Dirt Track Doug"
>
> ****************
>
>
> From: "Albaugh, Neil" <albaugh_neil@ti.com>
> Reply-To: "Albaugh, Neil" <albaugh_neil@ti.com>
> To: "'Nafzger'" <nafzger@vtc.net>, "'Terry Hunt'" <guambomb743@msn.com>,
> land-speed@autox.team.net
> Subject: RE: carb. leak
> Date: Wed, 4 Sep 2002 11:07:30 -0500
>
> Howard;
>
> Thanks for the note. I've also used it to seal Corvair cases as well as
> pushrod tubes.
>
> We used Hylomar to seal a Hewland
>
> -----Original Message-----
> From: Nafzger [mailto:nafzger@vtc.net]
> Sent: Tuesday, September 03, 2002 6:59 PM
> To: Albaugh, Neil; 'Terry Hunt'; land-speed@autox.team.net
> Subject: Re: carb. leak
>
>
> Neil,
> Hylomar is what BMW used to use on the pushrod tubes of the "Boxer Twins".
I
> also successfully used it on Corvair and VW pushrod tubes. Good stuff.
> Howard
>
> ----- Original Message -----
> From: "Albaugh, Neil" <albaugh_neil@ti.com>
> To: "'Terry Hunt'" <guambomb743@msn.com>; <land-speed@autox.team.net>
> Sent: Tuesday, September 03, 2002 4:49 PM
> Subject: RE: carb. leak
>
>
> > Terry;
> >
> > I like Hylomar sealant. It is gasoline fuel- proof but it comes off
> easily
> > with acetone or, better yet-- MEK.
> >
> > Regards, Neil Tucson, AZ
/// unsubscribe/change address requests to majordomo@autox.team.net or try
/// http://www.team.net/mailman/listinfo
/// Archives at http://www.team.net/archive/land-speed
/// what is needed. It isn't that difficult, folks.
|