healeys
[Top] [All Lists]

Re: [Healeys] O/D Problem Fixed

To: Healeys <healeys@autox.team.net>, Bob Spidell <bspidell@comcast.net>
Subject: Re: [Healeys] O/D Problem Fixed
From: Hank Leach <gradea1@charter.net>
Date: Wed, 18 Nov 2026 02:04:16 +0000 b63EtHhMiGOUWapiJ7JnBrz1vK+F6UN+oRs4C6bQpgZpbuOr97vqFyfy8KaRFQVT/Cd6+oWHbR8Mufc2+jd/H6rsJAeLFMGsCeCDLB81koN773ZeFfBPV5FT
Authentication-results: autox.team.net;
Delivered-to: mharc@autox.team.net
Delivered-to: healeys@autox.team.net
--===============3919093360270855329==
Content-Transfer-Encoding: quoted-printable

<div>Bob and all- the comment:<strong> 'If the solenoid went bad, could you=
 just replace the coil'</strong> is in fact possible. However, as with most=
 British and Lucas parts not everything is that easy to swap out as you =
know. The plunger itself had a Lucas part number: 766555 fitting to the =
761515 solenoid (circa 1959).</div>
<div>&nbsp;</div>
<div>However there were two different solenoids used on the Healey. The 100=
 &amp; 100-6 used the 76515 unit but the 3000 went to a different style =
76525.&nbsp; I seem to recall that the plungers are not interchangeable =
(thickness). Of course when purchasing a solenoid it often came with its =
matched plunger.</div>
<div>&nbsp;</div>
<div>On the early 100 overdrive =
the plunger was actually adjustable and had a longer arm (lever) but later =
they went to a fixed style and a shorter lever.</div>
<div>&nbsp;</div>
<div>The fascia mounted toggle switch was not actually a Lucas part but =
made by a British switch manufacturer-name escapes me- but Kent Lambert =
knew them and actually rebuilt them! Now-a-days you buy one and take your =
chances as you discovered with the elegant Moss replacement. Hank</div>
<div><br>-------------------- <br><br>From: "Bob Spidell via Healeys" =
&lt;healeys@autox.team.net&gt; <br>Reply-To: "Bob Spidell" =
&lt;bspidell@comcast.net&gt; <br>To: "Healeys" &lt;healeys@autox.team.=
net&gt; <br>Sent: November 17, 2026 at 4:27 PM PST <br>Subject: [Healeys] =
O/D Problem Fixed <br>Finally pulled the tunnel and futzed with the =
circuits. It turns out, it was a faulty (dash/fascia) switch. I fooled =
myself thinking, because I had the dash switch and the shifter knob switch =
wired in parallel one would work even if the other wouldn't (and vice =
versa). I had the two wires each ganged up on the dash switch, and when we =
pulled it out it fell apart. My basic understanding of electronics is that =
a parallel circuit will be live when any other circuit is wired to it =
proved not to be the case. I can't for the likes of me explain why, but =
that's what we found and fixed. Must have been a ground or short in the =
dash switch; the new one, sourced from Moss via Tom Monaco appeared to be =
better quality (that's the second one that's gone bad one me).<br>While I =
was debugging I got to&nbsp; wondering: 'If the solenoid went bad, could =
you just replace the coil (the plunger is free to fall)?'&nbsp; I know, to =
be extra careful super-duper sure you need to readjust the throw but, in a =
pinch it would be a lot easier than swapping the whole solenoid and =
readjusting the plunder throw. Bob ________________________________________=
_______ Support Team.Net http://www.team.net/donate.html Suggested annual =
donation $12.75 Archive: http://www.team.net/pipermail/healeys http://autox=
.team.net/archive/healeys Healeys@autox.team.net http://autox.team.=
net/mailman/listinfo/healeys Unsubscribe/Manage: http://autox.team.=
net/mailman/options/healeys/gradea1@charter.=
net</div>

--===============3919093360270855329==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________

Archive: http://www.team.net/pipermail/healeys 
http://autox.team.net/archive/healeys

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys



--===============3919093360270855329==--

<Prev in Thread] Current Thread [Next in Thread>