--===============1563069979802508075==
boundary="=_c5223dfc635f1820b765872105980b4c"
--=_c5223dfc635f1820b765872105980b4c
Content-Transfer-Encoding: quoted-printable
BOTH BJ7 AND BJ8 TRANSMISSIONS USE THE SAME ROLL PINS, AEA558 (2 ea.).=
=0ABut only the BJ7 MKII box uses the brass bush with circlip. You must=
=0Ause the correct stick depending on which bushing you are using in the=
=0Aproper tower. See previous note to Simon with stick part numbers-ther=
e=0Awere three different ones. Somehow OD is also a factor for correct=
=0Afit. Hank=0A=0A=09-----------------------------------------From: "ric=
hard mayor via=0AHealeys" =0ATo: "healeys"=0ACc: =0ASent: Friday Decembe=
r 3 2021 8:39:51AM=0ASubject: [Healeys] Center change gear sticks=0A=0A=
I have a top cover for what I thought was for a BJ8. I have no stick=
=0Aand no bushings - just the bare cover. I has the roll pins in place.=
=0ADoes this mean it is for a BJ7 and not a BJ8? =0A And if it came from=
a BJ7 can it still be used on a BJ8 transmission=0Aassuming one could f=
ind the proper stick and bushing? =0A=0A Thanks, Richard=0A
--=_c5223dfc635f1820b765872105980b4c
Content-Transfer-Encoding: quoted-printable
<html><body>Both BJ7 and BJ8 transmissions use the <b>same roll pins,</b=
> AEA558 (2 ea.). But only the BJ7 MKII box uses the brass bush with cir=
clip. You must use the correct stick depending on which bushing you are=
using in the proper tower. See previous note to Simon with stick part n=
umbers-there were three different ones. Somehow OD is also a factor for=
correct fit. Hank<br><br><div class=3D"reply-new-signature"></div><p>--=
---------------------------------------</p>From: "richard mayor via Heal=
eys" <healeys@autox.team.net><br>To: "healeys"<br>Cc: <br>Sent: Friday D=
ecember 3 2021 8:39:51AM<br>Subject: [Healeys] Center change gear sticks=
<br><br>=0A<div dir=3D"ltr">=0A<div>I have a top cover for what I though=
t was for a BJ8. I=0Ahave no stick and no bushings - just the bare=
cover. I has=0Athe roll pins in place. Does this mean it i=
s for a BJ7 and=0Anot a BJ8?</div>=0A<div><br></div>=0A<div>And if it ca=
me from a BJ7 can it still be used on a BJ8=0Atransmission assuming one=
could find the proper stick and=0Abushing? <br></div>=0A<div><br><=
/div>=0A<div>Thanks, Richard<br></div>=0A</div>=0A</healeys@autox.=
team.net></body></html>
--=_c5223dfc635f1820b765872105980b4c--
--===============1563069979802508075==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============1563069979802508075==--
|