This is a multipart message in MIME format.
--===============5917050690911495333==
boundary="----=_NextPart_000_0001_01D7AEFE.7BD91730"
Content-Language: en-us
This is a multipart message in MIME format.
------=_NextPart_000_0001_01D7AEFE.7BD91730
charset="utf-8"
Content-Transfer-Encoding: quoted-printable
Make sure the clutch is centered.
=20
Showed up to a friends a few weeks ago to help him install his TR6 =
transmission. =20
=20
After 90 minutes of struggle, we double checked the centering of the =
clutch and discovered that he had not fully inserted the clutch =
alignment tool into the pilot bearing, so he thought it was centered, =
but it was not.
=20
After proper centering, we popped it on in 5 =
minutes=E2=80=A6=E2=80=A6=E2=80=A6=E2=80=A6
=20
=20
=20
=20
From: Healeys <healeys-bounces@autox.team.net> On Behalf Of David P
Sent: Tuesday, September 21, 2021 2:43 PM
To: healeys@autox.team.net
Subject: Re: [Healeys] tranny installation--BJ8
=20
A light coat of oil on the splines aids the insertion.. after that it =
requires muscle for the first 1" to get parallelism of the splines... =
Muscle.
On 9/21/2021 3:34 PM, Bob Spidell wrote:
I've done this a few times; IIRC it always takes a bit of fiddling to =
get them to mate up. How far out is it; an inch or so the first motion =
shaft is probably butting-up against the spigot bearing, any more and =
you might be facing the same issue Simon said he had?
On 9/21/2021 2:18 PM, richard mayor via Healeys wrote:
Can you be more specific? Not sure why you even have the shifter still =
attached. It can poke you in the eye. You just need to make sure the =
tranny is in one of the gears so you can rotate the output shaft if =
necessary to make the input shaft splines mate with the clutch splines.=20
=20
On Tue, Sep 21, 2021 at 1:11 PM Tom Felts via Healeys =
Try as two of us can, we could not get the tranny back in the car. Is =
there a specific position it has to be to mate? I heard the shifter at =
about the 10 oclock position but that didn't seem to work.
=20
=20
=20
tom
=20
_______________________________________________
=20
Archive: http://www.team.net/pipermail/healeys =
http://autox.team.net/archive
=20
http://autox.team.net/mailman/listinfo/healeys
=20
http://autox.team.net/mailman/options/healeys/frogeye@porterscustom.com
=20
--=20
Porter Custom Bicycles 2909 Arno St. NE Albuquerque, NM. 505-352-1378 My =
World go here: WWW.PORTERBIKES.COM/ <http://WWW.PORTERBIKES.COM/>=20
------=_NextPart_000_0001_01D7AEFE.7BD91730
charset="utf-8"
Content-Transfer-Encoding: quoted-printable
<html xmlns:v=3D"urn:schemas-microsoft-com:vml" =
xmlns:o=3D"urn:schemas-microsoft-com:office:office" =
xmlns:w=3D"urn:schemas-microsoft-com:office:word" =
xmlns:m=3D"http://schemas.microsoft.com/office/2004/12/omml"; =
xmlns=3D"http://www.w3.org/TR/REC-html40";><head><meta =
http-equiv=3DContent-Type content=3D"text/html; charset=3Dutf-8"><meta =
name=3DGenerator content=3D"Microsoft Word 15 (filtered =
medium)"><style><!--
/* Font Definitions */
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
@font-face
{font-family:Consolas;
panose-1:2 11 6 9 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
pre
{mso-style-priority:99;
mso-style-link:"HTML Preformatted Char";
margin:0in;
font-size:10.0pt;
font-family:"Courier New";}
span.HTMLPreformattedChar
{mso-style-name:"HTML Preformatted Char";
mso-style-priority:99;
mso-style-link:"HTML Preformatted";
font-family:Consolas;}
span.EmailStyle20
{mso-style-type:personal-reply;
font-family:"Calibri",sans-serif;
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-size:10.0pt;}
@page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext=3D"edit" spidmax=3D"1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext=3D"edit">
<o:idmap v:ext=3D"edit" data=3D"1" />
</o:shapelayout></xml><![endif]--></head><body lang=3DEN-US link=3Dblue =
vlink=3Dpurple style=3D'word-wrap:break-word'><div =
class=3DWordSection1><p class=3DMsoNormal>Make sure the clutch is =
centered.<o:p></o:p></p><p class=3DMsoNormal><o:p> </o:p></p><p =
class=3DMsoNormal>Showed up to a friends a few weeks ago to help him =
install his TR6 transmission. <o:p></o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p class=3DMsoNormal>After 90 =
minutes of struggle, we double checked the centering of the clutch and =
discovered that he had not fully inserted the clutch alignment tool into =
the pilot bearing, so he thought it was centered, but it was =
not.<o:p></o:p></p><p class=3DMsoNormal><o:p> </o:p></p><p =
class=3DMsoNormal>After proper centering, we popped it on in 5 =
minutes=E2=80=A6=E2=80=A6=E2=80=A6=E2=80=A6<o:p></o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><div><div =
style=3D'border:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0in =
0in 0in'><p class=3DMsoNormal><b>From:</b> Healeys =
<healeys-bounces@autox.team.net> <b>On Behalf Of </b>David =
P<br><b>Sent:</b> Tuesday, September 21, 2021 2:43 PM<br><b>To:</b> =
healeys@autox.team.net<br><b>Subject:</b> Re: [Healeys] tranny =
installation--BJ8<o:p></o:p></p></div></div><p =
class=3DMsoNormal><o:p> </o:p></p><p>A light coat of oil on the =
splines aids the insertion.. after that it requires muscle for the first =
1" to get parallelism of the splines... =
Muscle.<o:p></o:p></p><div><p class=3DMsoNormal>On 9/21/2021 3:34 PM, =
Bob Spidell wrote:<o:p></o:p></p></div><blockquote =
style=3D'margin-top:5.0pt;margin-bottom:5.0pt'><p class=3DMsoNormal =
style=3D'margin-bottom:12.0pt'>I've done this a few times; IIRC it =
always takes a bit of fiddling to get them to mate up. How far out is =
it; an inch or so the first motion shaft is probably butting-up against =
the spigot bearing, any more and you might be facing the same issue =
Simon said he had?<o:p></o:p></p><div><p class=3DMsoNormal>On 9/21/2021 =
2:18 PM, richard mayor via Healeys =
wrote:<o:p></o:p></p></div><blockquote =
style=3D'margin-top:5.0pt;margin-bottom:5.0pt'><div><p =
class=3DMsoNormal>Can you be more specific? Not sure why you =
even have the shifter still attached. It can poke you in the eye. =
You just need to make sure the tranny is in one of the gears so =
you can rotate the output shaft if necessary to make the input shaft =
splines mate with the clutch splines. <o:p></o:p></p></div><p =
class=3DMsoNormal><o:p> </o:p></p><div><div><p class=3DMsoNormal>On =
Tue, Sep 21, 2021 at 1:11 PM Tom Felts via Healeys <<a =
href=3D"mailto:healeys@autox.team.net";>healeys@autox.team.net</a>> =
wrote:<o:p></o:p></p></div><blockquote =
style=3D'border:none;border-left:solid #CCCCCC 1.0pt;padding:0in 0in 0in =
6.0pt;margin-left:4.8pt;margin-top:5.0pt;margin-right:0in;margin-bottom:5=
.0pt'><div><div><p class=3DMsoNormal>Try as two of us can, we could not =
get the tranny back in the car. Is there a specific position it has to =
be to mate? I heard the shifter at about the 10 oclock position =
but that didn't seem to work.<o:p></o:p></p></div><div><p =
class=3DMsoNormal><o:p> </o:p></p></div><div><p =
class=3DMsoNormal><o:p> </o:p></p></div><div><p =
class=3DMsoNormal><o:p> </o:p></p></div><div><p =
class=3DMsoNormal>tom<o:p></o:p></p></div></div><p =
class=3DMsoNormal><o:p> </o:p></p></blockquote></div></blockquote><p=
class=3DMsoNormal =
style=3D'margin-bottom:12.0pt'><br><br><o:p></o:p></p><pre>______________=
_________________________________<o:p></o:p></pre><pre>Support Team.Net =
<a =
href=3D"http://www.team.net/donate.html";>http://www.team.net/donate.html<=
/a><o:p></o:p></pre><pre>Suggested annual donation =
$12.75<o:p></o:p></pre><pre><o:p> </o:p></pre><pre>Archive: <a =
href=3D"http://www.team.net/pipermail/healeys";>http://www.team.net/piperm=
ail/healeys</a> <a =
href=3D"http://autox.team.net/archive";>http://autox.team.net/archive</a><=
o:p></o:p></pre><pre><o:p> </o:p></pre><pre><a =
href=3D"mailto:Healeys@autox.team.net";>Healeys@autox.team.net</a><o:p></o=
:p></pre><pre><a =
href=3D"http://autox.team.net/mailman/listinfo/healeys";>http://autox.team=
.net/mailman/listinfo/healeys</a><o:p></o:p></pre><pre><o:p> </o:p><=
/pre><pre>Unsubscribe/Manage: <a =
href=3D"http://autox.team.net/mailman/options/healeys/frogeye@porterscust=
om.com">http://autox.team.net/mailman/options/healeys/frogeye@porterscust=
om.com</a><o:p></o:p></pre><pre><o:p> </o:p></pre></blockquote><pre>=
-- <o:p></o:p></pre><pre>Porter Custom Bicycles 2909 Arno St. NE =
Albuquerque, NM. 505-352-1378 My World go here: <a =
href=3D"http://WWW.PORTERBIKES.COM/";>WWW.PORTERBIKES.COM/</a><o:p></o:p><=
/pre></div></body></html>
------=_NextPart_000_0001_01D7AEFE.7BD91730--
--===============5917050690911495333==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============5917050690911495333==--
|