This is a multipart message in MIME format.
--===============1830124097707014137==
boundary="----=_NextPart_000_02CC_01D12141.E5E620B0"
Content-Language: en-us
This is a multipart message in MIME format.
------=_NextPart_000_02CC_01D12141.E5E620B0
charset="UTF-8"
Content-Transfer-Encoding: quoted-printable
Michael: can you share with us who you use for the Jet-Hot coating?
=20
Thanks,
=20
Al Fuller
al at bighealey dot org
'65 BJ-8
'85 Rx-7
=20
From: Healeys [mailto:healeys-bounces@autox.team.net] On Behalf Of =
Michael Oritt
Sent: Sunday, November 15, 2015 10:11 AM
To: Bob Spidell <bspidell@comcast.net>
Cc: healeys <healeys@autox.team.net>
Subject: Re: [Healeys] Jet-coating, wrap or do nothing to stainless =
headers?
=20
I had the DW header pipes on my 100 wrapped with heat tape for about two =
years, then took it off and went to a reflective shield. I noticed no =
deterioration of the pipes when I changed over to the shield and that =
was ten years ago.
=20
I don't believe that polishing is not the way to go as sometimes the =
process brings impurities to the surface and causes a lot of corrosion, =
esp. in SS. I have Jet-Hot coating or the like on the headers of all of =
my race cars and everything is intact and nice and shiny! =20
=20
Best--Michael Oritt
=20
On Sun, Nov 15, 2015 at 9:52 AM, Bob Spidell <bspidell@comcast.net =
I'll add that, although I wrapped the mild steel downpipes on my BJ8 and =
have no problems--that I know of--I've become reluctant to recommend it. =
I've seen photographic evidence of pipes being severely eroded by =
wrapping; though it appears to be a hit-or-miss issue, and may be due, =
in part, to how they were wrapped and what they were wrapped with (I =
have to believe if it was a very common problem nobody would buy the =
wrap and companies would cease to sell it). I wouldn't expect ceramic =
coating to be a problem, at least if the pipes were coated both inside =
and outside (inside only might even be better).
=20
Here in the colonies we mostly have to use gas with 10% ethanol ('pure' =
gas is available at some stations, but it's relatively rare). On a warm =
day, if my engine is hot and shut down for less than a couple hours and =
restarted I'll get some stumbling until air flow has cooled everything =
off a bit. I can't say with absolute certainty that the gasahol is the =
problem, but I don't recall this ever happening before the new =
formulation became prevalent. I think ceramic coating the manifold =
might cure this problem.
=20
Bob
=20
_____ =20
>
Sent: Sunday, November 15, 2015 2:28:55 AM
Subject: Re: [Healeys] Jet-coating, wrap or do nothing to stainless =
headers?
=20
Mirror polish them and leave them alone. Wrapping may lead to burning =
the metal away, coating possibly a similar story. By polishing you =
reduce the radiation of heat so the carbs should remain relatively cool. =
Anyway Webers/DellOrto's do not have the tendency to boil fuel. Also a =
car with an electric fuel pump does not normally have problems with fuel =
vapour lock.
Kees Oudesluijs
Op 15-11-2015 om 11:11 schreef Simon Lachlan:
I have stainless headers going down into a big bore(?) exhaust.
Opinions seem to vary as to the merits of wrapping, coating or doing =
nothing to them .
I have Webers above them, but I suspect, in my ignorance, that these are =
maybe less prone to evaporation issues than SUs.
What does the panel think?
See attached for a well researched synopsis. (Not by me!)
Simon
\
=20
=20
_______________________________________________
Archive: http://www.team.net/archive
http://autox.team.net/mailman/listinfo/healeys
http://autox.team.net/mailman/options/healeys/michael.oritt@gmail.com
=20
------=_NextPart_000_02CC_01D12141.E5E620B0
charset="UTF-8"
Content-Transfer-Encoding: quoted-printable
<html xmlns:v=3D"urn:schemas-microsoft-com:vml" =
xmlns:o=3D"urn:schemas-microsoft-com:office:office" =
xmlns:w=3D"urn:schemas-microsoft-com:office:word" =
xmlns:m=3D"http://schemas.microsoft.com/office/2004/12/omml" =
xmlns=3D"http://www.w3.org/TR/REC-html40"><head><meta =
http-equiv=3DContent-Type content=3D"text/html; charset=3Dutf-8"><meta =
name=3DGenerator content=3D"Microsoft Word 15 (filtered medium)"><!--[if =
!mso]><style>v\:* {behavior:url(#default#VML);}
o\:* {behavior:url(#default#VML);}
w\:* {behavior:url(#default#VML);}
.shape {behavior:url(#default#VML);}
</style><![endif]--><style><!--
/* Font Definitions */
@font-face
{font-family:Helvetica;
panose-1:2 11 6 4 2 2 2 2 2 4;}
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:12.0pt;
font-family:"Times New Roman",serif;}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:purple;
text-decoration:underline;}
span.EmailStyle17
{mso-style-type:personal-reply;
font-family:"Calibri",sans-serif;
color:#1F497D;}
.MsoChpDefault
{mso-style-type:export-only;
font-family:"Calibri",sans-serif;}
@page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext=3D"edit" spidmax=3D"1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext=3D"edit">
<o:idmap v:ext=3D"edit" data=3D"1" />
</o:shapelayout></xml><![endif]--></head><body lang=3DEN-US link=3Dblue =
vlink=3Dpurple><div class=3DWordSection1><p class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri",sans-serif;color:#1F497D'=
>Michael:=C2=A0 can you share with us who you use for the Jet-Hot =
coating?<o:p></o:p></span></p><p class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri",sans-serif;color:#1F497D'=
><o:p> </o:p></span></p><p class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri",sans-serif;color:#1F497D'=
>Thanks,<o:p></o:p></span></p><p class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri",sans-serif;color:#1F497D'=
><o:p> </o:p></span></p><p class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri",sans-serif;color:#1F497D'=
>Al Fuller</span><span style=3D'color:black'><o:p></o:p></span></p><p =
class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri",sans-serif;color:#1F497D'=
>al at bighealey dot org</span><span =
style=3D'color:black'><o:p></o:p></span></p><p class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri",sans-serif;color:#1F497D'=
>'65 BJ-8</span><span style=3D'color:black'><o:p></o:p></span></p><p =
class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri",sans-serif;color:#1F497D'=
>'85 Rx-7</span><span style=3D'color:black'><o:p></o:p></span></p><p =
class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri",sans-serif;color:#1F497D'=
><o:p> </o:p></span></p><p class=3DMsoNormal><b><span =
style=3D'font-size:11.0pt;font-family:"Calibri",sans-serif'>From:</span><=
/b><span style=3D'font-size:11.0pt;font-family:"Calibri",sans-serif'> =
Healeys [mailto:healeys-bounces@autox.team.net] <b>On Behalf Of =
</b>Michael Oritt<br><b>Sent:</b> Sunday, November 15, 2015 10:11 =
AM<br><b>To:</b> Bob Spidell <bspidell@comcast.net><br><b>Cc:</b> =
healeys <healeys@autox.team.net><br><b>Subject:</b> Re: [Healeys] =
Jet-coating, wrap or do nothing to stainless =
headers?<o:p></o:p></span></p><p =
class=3DMsoNormal><o:p> </o:p></p><div><div><p =
class=3DMsoNormal><span style=3D'color:#3333FF'>I had the DW header =
pipes on my 100 wrapped with heat tape for about two years, then took it =
off and went to a reflective shield. I noticed no deterioration of =
the pipes when I changed over to the shield and that was ten years =
ago.<o:p></o:p></span></p></div><div><p class=3DMsoNormal><span =
style=3D'color:#3333FF'><o:p> </o:p></span></p></div><div><p =
class=3DMsoNormal><span style=3D'color:#3333FF'>I don't believe that =
polishing is not the way to go as sometimes the process brings =
impurities to the surface and causes a lot of corrosion, esp. in =
SS. I have Jet-Hot coating or the like on the headers of all of my =
race cars and everything is intact and nice and shiny! =
<o:p></o:p></span></p></div><div><p class=3DMsoNormal><span =
style=3D'color:#3333FF'><o:p> </o:p></span></p></div><div><p =
class=3DMsoNormal><span style=3D'color:#3333FF'>Best--Michael =
Oritt<o:p></o:p></span></p></div></div><div><p =
class=3DMsoNormal><o:p> </o:p></p><div><p class=3DMsoNormal>On Sun, =
Nov 15, 2015 at 9:52 AM, Bob Spidell <<a =
href=3D"mailto:bspidell@comcast.net" =
target=3D"_blank">bspidell@comcast.net</a>> =
wrote:<o:p></o:p></p><blockquote style=3D'border:none;border-left:solid =
#CCCCCC 1.0pt;padding:0in 0in 0in =
6.0pt;margin-left:4.8pt;margin-right:0in'><div><div><div><p =
class=3DMsoNormal><span =
style=3D'font-family:"Arial",sans-serif;color:black'>I'll add that, =
although I wrapped the mild steel downpipes on my BJ8 and have no =
problems--that I know of--I've become reluctant to recommend it. =
I've seen photographic evidence of pipes being severely eroded by =
wrapping; though it appears to be a hit-or-miss issue, and may be due, =
in part, to how they were wrapped and what they were wrapped with (I =
have to believe if it was a very common problem nobody would buy the =
wrap and companies would cease to sell it). I wouldn't expect =
ceramic coating to be a problem, at least if the pipes were coated both =
inside and outside (inside only might even be =
better).<o:p></o:p></span></p></div><div><p class=3DMsoNormal><span =
style=3D'font-family:"Arial",sans-serif;color:black'><o:p> </o:p></s=
pan></p></div><div><p class=3DMsoNormal><span =
style=3D'font-family:"Arial",sans-serif;color:black'>Here in the =
colonies we mostly have to use gas with 10% ethanol ('pure' gas is =
available at some stations, but it's relatively rare). On a warm =
day, if my engine is hot and shut down for less than a couple hours and =
restarted I'll get some stumbling until air flow has cooled everything =
off a bit. I can't say with absolute certainty that the gasahol is =
the problem, but I don't recall this ever happening before the new =
formulation became prevalent. I think ceramic coating the manifold =
might cure this problem.<o:p></o:p></span></p></div><div><p =
class=3DMsoNormal><span =
style=3D'font-family:"Arial",sans-serif;color:black'><o:p> </o:p></s=
pan></p></div><div><p class=3DMsoNormal><span =
style=3D'font-family:"Arial",sans-serif;color:black'>Bob<o:p></o:p></span=
></p></div><div><p class=3DMsoNormal><span =
style=3D'font-family:"Arial",sans-serif;color:black'><o:p> </o:p></s=
pan></p></div><div class=3DMsoNormal align=3Dcenter =
style=3D'text-align:center'><span =
style=3D'font-family:"Arial",sans-serif;color:black'><hr size=3D2 =
width=3D"100%" align=3Dcenter></span></div><div><p =
class=3DMsoNormal><b><span =
style=3D'font-family:"Helvetica",sans-serif;color:black'>From: =
</span></b><span =
style=3D'font-family:"Helvetica",sans-serif;color:black'>"Oudesluys&=
quot; <<a href=3D"mailto:coudesluijs@chello.nl" =
target=3D"_blank">coudesluijs@chello.nl</a>><br><b>To: =
</b>"healeys" <<a href=3D"mailto:healeys@autox.team.net" =
target=3D"_blank">healeys@autox.team.net</a>><br><b>Sent: </b>Sunday, =
November 15, 2015 2:28:55 AM<br><b>Subject: </b>Re: [Healeys] =
Jet-coating, wrap or do nothing to stainless =
headers?<o:p></o:p></span></p><div><p class=3DMsoNormal><span =
style=3D'font-family:"Helvetica",sans-serif;color:black'><o:p> </o:p=
></span></p></div><div><p class=3DMsoNormal><span =
style=3D'font-family:"Helvetica",sans-serif;color:black'>Mirror polish =
them and leave them alone. Wrapping may lead to burning the metal away, =
coating possibly a similar story. By polishing you reduce the radiation =
of heat so the carbs should remain relatively cool. Anyway =
Webers/DellOrto's do not have the tendency to boil fuel. Also a car with =
an electric fuel pump does not normally have problems with fuel vapour =
lock.<br>Kees Oudesluijs<br><br><br><br><br>Op 15-11-2015 om 11:11 =
schreef Simon Lachlan:<o:p></o:p></span></p></div><blockquote =
style=3D'margin-top:5.0pt;margin-bottom:5.0pt'><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
style=3D'color:black'>I have stainless headers going down into a big =
bore(?) exhaust.<o:p></o:p></span></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
style=3D'color:black'>Opinions seem to vary as to the merits of =
wrapping, coating or doing nothing to them .<o:p></o:p></span></p><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
style=3D'color:black'>I have Webers above them, but I suspect, in my =
ignorance, that these are maybe less prone to evaporation issues than =
SUs.<o:p></o:p></span></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
style=3D'color:black'>What does the panel think?<o:p></o:p></span></p><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
style=3D'color:black'>See attached for a well researched synopsis. (Not =
by me!)<o:p></o:p></span></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
style=3D'color:black'>Simon<o:p></o:p></span></p></div><p =
class=3DMsoNormal><span =
style=3D'font-family:"Helvetica",sans-serif;color:black'><br>\<o:p></o:p>=
</span></p></blockquote><div><p class=3DMsoNormal><span =
style=3D'font-family:"Helvetica",sans-serif;color:black'><o:p> </o:p=
></span></p></div></div><div><p class=3DMsoNormal><span =
style=3D'font-family:"Arial",sans-serif;color:black'><o:p> </o:p></s=
pan></p></div></div></div><p class=3DMsoNormal =
style=3D'margin-bottom:12.0pt'><br>______________________________________=
_________<br>Support Team.Net <a =
href=3D"http://www.team.net/donate.html" =
target=3D"_blank">http://www.team.net/donate.html</a><br>Suggested =
annual donation $12.75<br>Archive: <a =
href=3D"http://www.team.net/archive" =
target=3D"_blank">http://www.team.net/archive</a><br>Forums: <a =
href=3D"http://www.team.net/forums" =
target=3D"_blank">http://www.team.net/forums</a><br><br><a =
href=3D"mailto:Healeys@autox.team.net">Healeys@autox.team.net</a><br><a =
href=3D"http://autox.team.net/mailman/listinfo/healeys" =
target=3D"_blank">http://autox.team.net/mailman/listinfo/healeys</a><br><=
br>Unsubscribe/Manage: <a =
href=3D"http://autox.team.net/mailman/options/healeys/michael.oritt@gmail=
.com" =
target=3D"_blank">http://autox.team.net/mailman/options/healeys/michael.o=
ritt@gmail.com</a><br><br><o:p></o:p></p></blockquote></div><p =
class=3DMsoNormal><o:p> </o:p></p></div></div></body></html>
------=_NextPart_000_02CC_01D12141.E5E620B0--
--===============1830124097707014137==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============1830124097707014137==--
|