--===============2684658712395023515==
boundary="----=_Part_8996729_1786397151.1436126250080"
------=_Part_8996729_1786397151.1436126250080
Content-Transfer-Encoding: quoted-printable
I set the timing at 15 deg.btdc=C2=A0 =C2=A0at 650 r.p.m.=C2=A0=C2=A0=C2=A0=
now I have to adjust. carbs=C2=A0=C2=A0 .....they were rebuilt, again.....=
thanks Mitch=20
----- Original Message -----
From: "Oudesluys" <coudesluijs@chello.nl>=20
To: healeys@autox.team.net=20
Sent: Sunday, July 5, 2015 11:31:05 AM=20
Subject: Re: [Healeys] HELP............TIMING=20
Start the engine and let it idle until warm or drive a few miles to that pu=
rpose.=20
Set the idling speed at around 800-900rpm.=20
Set the dial to the required advance at idling with the vacuum line attache=
d (see your workshop manual). Connect up to the battery and position the cl=
amp on Nr.1 plug lead.=20
Loosen the distributor clamp.=20
Set the distributor to TDC on the marks.=20
Tighten the clamp, not to tight.=20
Recheck.=20
It is that simple.=20
WATCH OUT though for moving parts like the fan and water pump/dynamo pulley=
s/belts.=20
Kees Oudesluijs=20
Mitch schreef op 5-7-2015 om 15:51:=20
Hello ,=20
=C2=A0=20
I have a 1966 bj8.......I have just replaced my original Lucas distributer =
with a new Pertronics distributer .........I turned the engine until the po=
inter was on the tdc mark on the pulley (on the compression stroke) and put=
the rotor pointing at the #1 spark plug in the dist. cap................NO=
W what do I do? I have a timing light with the degree dial on the back,....=
...........what are the next steps to set the timing correctly?? do I plug =
the vacuum, what degrees,do I have to start the engine??? etc..............=
...................sorry for all the questions=20
=C2=A0=20
Mitch=20
_______________________________________________
$12.75
Archive: http://www.team.net/archive Forums: http://www.team.net/forums Hea=
leys@autox.team.net http://autox.team.net/mailman/listinfo/healeys Unsubscr=
ibe/Manage: http://autox.team.net/mailman/options/healeys/coudesluijs@chell=
o.nl=20
Geen virus gevonden in dit bericht.=20
Gecontroleerd door AVG - www.avg.com=20
Versie: 2015.0.6081 / Virusdatabase: 4392/10164 - datum van uitgifte: 07/05=
/15=20
_______________________________________________=20
Archive: http://www.team.net/archive=20
Healeys@autox.team.net=20
http://autox.team.net/mailman/listinfo/healeys=20
comcast.net=20
------=_Part_8996729_1786397151.1436126250080
Content-Transfer-Encoding: 7bit
<html><body><div style="font-family: Arial; font-size: 12pt; color:
#000000"><DIV aria-label="Compose body">I set the timing at 15 deg.btdc
at 650 r.p.m. now I have to adjust. carbs
.....they were rebuilt, again.....thanks Mitch<BR></DIV>
<DIV><BR></DIV>
<HR id=zwchr>
<DIV style="FONT-SIZE: 12pt; TEXT-DECORATION: none; FONT-FAMILY:
Helvetica,Arial,sans-serif; FONT-WEIGHT: normal; COLOR: #000; FONT-STYLE:
normal" data-mce-style="color: #000; font-weight: normal; font-style: normal;
text-decoration: none; font-family: Helvetica,Arial,sans-serif; font-size:
12pt;"><B>From: </B>"Oudesluys" <coudesluijs@chello.nl><BR><B>To:
</B>healeys@autox.team.net<BR><B>Sent: </B>Sunday, July 5, 2015 11:31:05
AM<BR><B>Subject: </B>Re: [Healeys] HELP............TIMING<BR>
<DIV><BR></DIV>
<DIV class=moz-cite-prefix><BR>Start the engine and let it idle until warm or
drive a few miles to that purpose.<BR>Set the idling speed at around
800-900rpm.<BR>Set the dial to the required advance at idling with the vacuum
line attached (see your workshop manual). Connect up to the battery and
position the clamp on Nr.1 plug lead.<BR>Loosen the distributor clamp.<BR>Set
the distributor to TDC on the marks.<BR>Tighten the clamp, not to
tight.<BR>Recheck.<BR>It is that simple.<BR><BR>WATCH OUT though for moving
parts like the fan and water pump/dynamo pulleys/belts.<BR>Kees
Oudesluijs<BR><BR><BR><BR>Mitch schreef op 5-7-2015 om 15:51:<BR></DIV>
<BLOCKQUOTE
cite=mid:237588308.8793043.1436104295976.JavaMail.zimbra@comcast.net>
<DIV>
<DIV>Hello ,</DIV>
<DIV> </DIV>
<DIV>I have a 1966 bj8.......I have just replaced my original Lucas distributer
with a new Pertronics distributer .........I turned the engine until the
pointer was on the tdc mark on the pulley (on the compression stroke) and put
the rotor pointing at the #1 spark plug in the dist. cap................NOW
what do I do? I have a timing light with the degree dial on the
back,...............what are the next steps to set the timing correctly?? do I
plug the vacuum, what degrees,do I have to start the engine???
etc.................................sorry for all the questions</DIV>
<DIV> </DIV>
<DIV>Mitch</DIV></DIV><BR>
<FIELDSET
class=mimeAttachmentHeader></FIELDSET><BR><PRE>_______________________________________________
Archive: <A class=moz-txt-link-freetext href="http://www.team.net/archive";
target=_blank
data-mce-href="http://www.team.net/archive";>http://www.team.net/archive</A>
Forums: <A class=moz-txt-link-freetext href="http://www.team.net/forums";
target=_blank
data-mce-href="http://www.team.net/forums";>http://www.team.net/forums</A>
<A class=moz-txt-link-abbreviated href="mailto:Healeys@autox.team.net";
target=_blank
data-mce-href="mailto:Healeys@autox.team.net";>Healeys@autox.team.net</A>
<A class=moz-txt-link-freetext
href="http://autox.team.net/mailman/listinfo/healeys"; target=_blank
data-mce-href="http://autox.team.net/mailman/listinfo/healeys";>http://autox.team.net/mailman/listinfo/healeys</A>
</PRE><BR>
<FIELDSET class=mimeAttachmentHeader></FIELDSET><BR>
<P>Geen virus gevonden in dit bericht.<BR>Gecontroleerd door AVG - <A
href="http://www.avg.com/"; target=_blank
data-mce-href="http://www.avg.com";>www.avg.com</A><BR>Versie: 2015.0.6081 /
Virusdatabase: 4392/10164 - datum van uitgifte:
07/05/15</P></BLOCKQUOTE><BR><BR>_______________________________________________<BR>Support
Team.Net http://www.team.net/donate.html<BR>Suggested annual donation
$12.75<BR>Archive: http://www.team.net/archive<BR>Forums:
http://www.team.net/forums<BR>
<DIV><BR></DIV>Healeys@autox.team.net<BR>http://autox.team.net/mailman/listinfo/healeys<BR>
<DIV><BR></DIV>Unsubscribe/Manage:
http://autox.team.net/mailman/options/healeys/dayton21@comcast.net<BR>
<DIV><BR></DIV></DIV>
<DIV><BR></DIV></div></body></html>
------=_Part_8996729_1786397151.1436126250080--
--===============2684658712395023515==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============2684658712395023515==--
|