--===============4304361251969255525==
boundary="----=_Part_3247384_21318721.1597845065393"
------=_Part_3247384_21318721.1597845065393
Content-Transfer-Encoding: 7bit
Hi,
I poked around in the archives and found a few TR6 references with Weber
jetting, but for the most part the references fail to mention the choke tubes
for the setups.
I've been running 28mm chokes since forever and was looking to swap in some
30mm chokes but I may have to do the swap without access to a dyno.
So, the question is: if you change to different choke tubes, do you need to
re-jet? I know the answer is yes, but I'd like to see some examples for folks
that have done this (change from 28's to 30's or similar).
If you don't want to share setups on the list, I understand, but I figured in
the interest of science, some real references would help establish a baseline.
And yes, I know how small changes in the jetting can pay dividends. I've seen 7
or 8 HP gains playing with air correctors!
Feel free to respond off list.
Regards,Bob Lang339-927-4489
------=_Part_3247384_21318721.1597845065393
Content-Transfer-Encoding: quoted-printable
<html><head></head><body><div class=3D"yahoo-style-wrap" style=3D"font-fami=
ly:Helvetica Neue, Helvetica, Arial, sans-serif;font-size:13px;"><div dir=
=3D"ltr" data-setdir=3D"false">Hi,</div><div dir=3D"ltr" data-setdir=3D"fal=
se"><br></div><div dir=3D"ltr" data-setdir=3D"false">I poked around in the =
archives and found a few TR6 references with Weber jetting, but for the mos=
t part the references fail to mention the choke tubes for the setups.</div>=
<div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setd=
ir=3D"false">I've been running 28mm chokes since forever and was looking to=
swap in some 30mm chokes but I may have to do the swap without access to a=
dyno.</div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"lt=
r" data-setdir=3D"false">So, the question is: if you change to different ch=
oke tubes, do you need to re-jet? I know the answer is yes, but I'd like to=
see some examples for folks that have done this (change from 28's to 30's =
or similar).</div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=
=3D"ltr" data-setdir=3D"false">If you don't want to share setups on the lis=
t, I understand, but I figured in the interest of science, some real refere=
nces would help establish a baseline. And yes, I know how small changes in =
the jetting can pay dividends. I've seen 7 or 8 HP gains playing with air c=
orrectors!</div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=
=3D"ltr" data-setdir=3D"false">Feel free to respond off list.<br></div><div=
dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=
=3D"false">Regards,</div><div dir=3D"ltr" data-setdir=3D"false">Bob Lang</d=
iv><div dir=3D"ltr" data-setdir=3D"false">339-927-4489<br></div></div></bod=
y></html>
------=_Part_3247384_21318721.1597845065393--
--===============4304361251969255525==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
--===============4304361251969255525==--
|