fot
[Top] [All Lists]

[Fot] TR4 ARP Flywheel Bolts Question

Subject: [Fot] TR4 ARP Flywheel Bolts Question
From: timmmurphh at gmail.com (timmmurphh at gmail.com)
Date: Sun, 4 Jun 2017 17:52:48 -0500
References: <1173587813.820995.1496435269367.ref@mail.yahoo.com> <1173587813.820995.1496435269367@mail.yahoo.com> <001901d2dd64$9cf0a390$d6d1eab0$@gmail.com> <000701d2dd7d$5c9e1480$15da3d80$@wi.rr.com>
Thanks for the clarification Steve, that makes sense.

 

Tim

 

 

From: Steve Yott [mailto:tr4 at wi.rr.com] 
Sent: Sunday, June 4, 2017 4:56 PM
To: timmmurphh at gmail.com; 'STEPHEN BOROWSKI' <biznzman at pacbell.net>
Subject: RE: [Fot] TR4 ARP Flywheel Bolts Question

 

The reason they state to not use washers is they are afraid that the washers 
used will (1) not be hard enough and will compress under the bolt head and (2) 
all ARP bolts have very liberal radii between the head and shank.  If there is 
a tight fitting washer this would be strain on this radius and could break the 
head.

 

The 7/16? ARP bolts used on Chevy flywheels is what I fit to TR?6, late 
Spitfires and modified TR4 cranks.  These bolts come with the special washers 
to use with them.  I have used a proper washer under the 3/8? ARP bolts many 
times with no problems using a correct washer.  You can also use an ARP crown 
wheel bolt for the same purpose and these come with proper washers.

 

Steve Yott  

 

From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of timmmurphh--- via 
Fot
Sent: Sunday, June 04, 2017 1:59 PM
Subject: Re: [Fot] TR4 ARP Flywheel Bolts Question

 

FWIW

 

I just got a set of ARP 206-2802 flywheel bolts from Pegasus for the TR4.  They 
are for ?BMC A series?.  The instruction specifically says, ?DO NOT USE ANY 
WAHERS?, yes, all in caps for emphasis!  They further state that ARP will not 
be responsible for failures is washers are used.  The instructions also say, 
?Make sure there is an adequate chamfer under the bolt holes on the flywheel to 
clear the radius under the head of the bolt.?  Torque is 55 Ft-Lb with 
specified lubricants on the threads.

 

I?ve never had that much good luck grinding the ends of bolts and still having 
it square so as not to start it cocked and runing the female threads.  Maybe 
it?s just me?

 

Tim

 

 

From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of STEPHEN BOROWSKI 
via Fot
Sent: Friday, June 2, 2017 3:28 PM
Subject: [Fot] TR4 ARP Flywheel Bolts Question

 

Does anyone have experience using the ARP flywheel bolts sold by Moss and 
others?

I understand that you may have to shorten the bolt or it breaks the rear seal???

Are they supposed to have a washer or not?

 

Thxs. Steve

-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/fot/attachments/20170604/820f6777/attachment.html>

<Prev in Thread] Current Thread [Next in Thread>