Just my opinion after many tractor motor rebuilds in all my years. I have
one of the long taps for this purpose and thought like many that I must
clean out those threads with a tap. Keep in mind that I still "chase" all
the other holes in the block but like Bob clean out the threads with a
standard head bolt. Why? After I began using a tap to clean out the
threads I had a couple of these holes pull out when doing a final torque
using ARP head studs. Since then I have gone back to only cleaning up the
threads with an old bolt and wire brush. Having one of the deep holes strip
out is a maddening problem and not easily repaired and usually requires a
new block!
The grooves on the studs are there to prevent oil from building up under the
stud which can cause a hydraulic lock and strip out the threads also. I
learned this working at Mercedes in the way back years....
I'm just saying..... be very careful!!!
Steve Yott
-----Original Message-----
From: fot-bounces@autox.team.net [mailto:fot-bounces@autox.team.net] On
Behalf Of Bob Kramer
Sent: Wednesday, January 08, 2014 3:27 PM
To: Greg And Alison Blake
Cc: FOT
Subject: Re: [Fot] Extended bottoming tap for TR4 engine
I just use old style Triumph studs with the grooves cut into the threads to
catch swarf, and lots of in and outs until they thread in by hand. This gas
always worked for me, but I suppose I should step up my game,
Bob Kramer
Sent from my iPhone
> On Jan 8, 2014, at 2:57 PM, Greg And Alison Blake
> <ablake2@austin.rr.com>
wrote:
>
> I just use a normal length bottoming tap and use a 1/4 socket
> extension to reach the bottom. You'll want to find the right size
> socket to marry up
with
> the tap and then use some tape or something in case the socket wants
> to separate from the tap upon removal.
>
>
>> On Jan 8, 2014, at 8:57 AM, marty <trmarty@hotmail.com> wrote:
>>
>> Hi John. I have one I made up that you are more than welcome to
>> borrow if
> you
>> would like. If so, email me your address and I can drop it in the mail.
>>
>>
>>
>> Marty
>>
>>
>>> Date: Wed, 8 Jan 2014 09:46:04 -0500
>>> From: johnstydo@gmail.com
>>> To: fot@autox.team.net
>>> Subject: [Fot] Extended bottoming tap for TR4 engine
>>>
>>> Does anyone have a tool source for a 1/2-13 extended bottoming tap
>>> to
> reach
>>> the four deep head studs on the TR4 pot? Looks like at least 6" OAL.
>>> Any comments on the value of bottom-tapping blind holes to improve
>>> stud holding? Thanks _______________________________________________
>>> fot@autox.team.net
>>>
>>> http://www.fot-racing.com
>>>
>>> Donate: http://www.team.net/donate.html
>>> Archive: http://www.team.net/archive
>>> Forums: http://www.team.net/forums
>>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/fot/trmarty@hotmail.com
>> _______________________________________________
>> fot@autox.team.net
>>
>> http://www.fot-racing.com
>>
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/fot/ablake2@austin.rr.com
> _______________________________________________
> fot@autox.team.net
>
> http://www.fot-racing.com
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
http://autox.team.net/mailman/options/fot/rkramer3@austin.rr.com
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
|