fot
[Top] [All Lists]

Re: [Fot] Spitfire head torque

To: Robert MacKenzie <list@mackenzie.aero>
Subject: Re: [Fot] Spitfire head torque
From: Chuck Gee <chasgee@aol.com>
Date: Mon, 15 Apr 2013 11:07:10 -0600
Cc: "<fot@autox.team.net>" <fot@autox.team.net>
Delivered-to: mharc@autox.team.net
Delivered-to: fot@autox.team.net
References: <1365867657.32068.YahooMailRC@web184803.mail.gq1.yahoo.com> <003f01ce39df$f4830300$dd890900$@aero> <BEAF639C-D360-4DF7-B336-EDF3096328A5@aol.com> <000601ce39fa$b74431b0$25cc9510$@aero>
Yes, 60 is the number if using regular oil.

Chuck

On Apr 15, 2013, at 11:00 AM, "Robert MacKenzie" <list@mackenzie.aero> wrote:

> Just to clarify; I do re-torque again after the engine is run and cooled.
> If I recall correctly I was given the 60 lbs figure from ARP.
>
> Robert
>
> -----Original Message-----
> From: Chuck Gee [mailto:chasgee@aol.com]
> Sent: Monday, April 15, 2013 10:07 AM
> To: Robert MacKenzie
> Cc: Tim Pettenati; <fot@autox.team.net>
> Subject: Re: [Fot] Spitfire head torque
>
> Just keep in mind that if you use the ARP lube the recommended torque is 40
> ft-lbs.  Also, if you tongue them hot you will be relieving the stretch
when
> the motor cools down.  This is not a good thing.  Proper stretch is what is
> important.
>
> Chuck
>
> On Apr 15, 2013, at 7:48 AM, "Robert MacKenzie" <list@mackenzie.aero>
wrote:
>
>> Tim:
>>
>> I have been using 60 ft/lbs on my 1147s with ARP studs/nuts and a
>> Payen gasket.  I pull to 60 with 3 pulls of 20, 40, then 60.  I let
>> the head sit overnight (cold) then retorque to 60 again.  Since
>> following this process I have had no issues with head gaskets.
>>
>> The ARP numbers for the studs are:
>>
>> Head Stud - AJ 4.250-1SFB
>> Nut - AJN 12-1
>> Washer - AJW 750N
>>
>> They can be ordered from Summit Racing along with the 10 stud 1500/1296
> kit.
>>
>> Robert MacKenzie
>>
>>
>>
>> -----Original Message-----
>> From: fot-bounces@autox.team.net [mailto:fot-bounces@autox.team.net]
>> On Behalf Of Tim Pettenati
>> Sent: Saturday, April 13, 2013 10:41 AM
>> To: fot@autox.team.net
>> Subject: [Fot] Spitfire head torque
>>
>> Checking on what folks are using for torque spec on head nuts?
>>
>> 1147cc
>> Spitfire with studs upgraded to 7/16" ARP and Payen gasket.
>>
>> Also if anyone
>> knows what the ARP partnumber is for the 7/16" studs.
>> I'm guessing they are
>> the same as the GT6/TR6 kit but would like to know for sure.
>>
>> Thanks,
>> Tim
>> _______________________________________________
>> fot@autox.team.net
>>
>> http://www.fot-racing.com
>>
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/fot/list@mackenzie.aero
>> _______________________________________________
>> fot@autox.team.net
>>
>> http://www.fot-racing.com
>>
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/fot/chasgee@aol.com
_______________________________________________
fot@autox.team.net

http://www.fot-racing.com

Archive: http://www.team.net/archive


<Prev in Thread] Current Thread [Next in Thread>